- 您现在的位置：买卖IC网 > PDF目录20504 > RDK-158 (Power Integrations)KIT REF DESIGN PG LINKSWITCH-II PDF资料下载
参数资料
| 型号： | RDK-158 |
| 厂商： | Power Integrations |
| 文件页数： | 5/18页 |
| 文件大小： | 0K |
| 描述： | KIT REF DESIGN PG LINKSWITCH-II |
| 应用说明： | LinkSwitch-II Family, Appl Note AN-44 |
| 设计资源： | RDR-158, 5W Charger Using LNK616PG |
| 标准包装： | 1 |
| 系列： | LinkSwitch®-II |
| 主要目的： | AC/DC，主面 |
| 输出及类型： | 1，隔离 |
| 功率 - 输出： | 5W |
| 输出电压： | 4.75 ~ 5.25 V |
| 电流 - 输出： | 1A |
| 输入电压： | 85 ~ 265VAC |
| 稳压器拓扑结构： | 回扫 |
| 频率 - 开关： | 67.25 kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | LNK603，LNK604，LNK605，LNK606，LNK613，LNK614，LNK615，LNK616 |
| 其它名称： | 596-1311 |
LNK603-606/613-616
Device
istic and frequency control for constant current (CC) regulation.
The feedback resistors (R5 and R6) were selected using
standard 1% resistor values to center both the nominal output
voltage and constant current regulation thresholds.
Key Application Considerations
LinkSwitch-II Output Cable Voltage Drop Compensation
BYPASS Pin Output Voltage
Capacitor Value Change Factor
1 m F 1.035
LNK613
10 m F 1.055
Output Power Table
LNK614
1 m F
10 m F
1.045
1.065
The data sheet maximum output power table (Table 1) repre-
sents the maximum practical continuous output power level
that can be obtained under the following assumed conditions:
1. The minimum DC input voltage is 90 V or higher at 85 VAC
input. The value of the input capacitance should be large
enough to meet these criteria for AC input designs.
2. Secondary output of 5 V with a Schottky rectifier diode.
3. Assumed efficiency of 70%.
4. Discontinuous mode operation (K P >1.3).
5. The part is board mounted with SOURCE pins soldered to a
sufficient area of copper to keep the SOURCE pin tempera-
ture at or below 90 °C.
6. Ambient temperature of 50 °C for open frame designs and
an internal enclosure temperature of 60 °C for adapter
designs.
Note: Higher output power are achievable if an output CC
tolerance >±10% is acceptable, allowing the device to be
operated at a higher SOURCE pin temperature.
Output Tolerance
LinkSwitch-II provides an overall output tolerance (including line,
component variation and temperature) of ±5% for the output
voltage in CV operation and ±10% for the output current during
CC operation over a junction temperature range of 0 °C to 100 °C
for the P/G package. For the D package (SO8) additional CC
variance may occur due to stress caused by the manufacturing
flow (i.e. solder-wave immersion or IR reflow). A sample power
supply build is recommended to verify production tolerances for
each design.
BYPASS Pin Capacitor Selection
For LinkSwitch-II 60x Family of Devices (without output
cable voltage drop compensation)
A 1 m F BYPASS pin capacitor is recommended. The capacitor
voltage rating should be greater than 7 V. The capacitor’s
dielectric material is not important but tolerance of capacitor
should be ≤ ±50%. The capacitor must be physically located
close to the LinkSwitch-II BYPASS pin.
For LinkSwitch-II 61x Family of Devices (with output cable
voltage drop compensation)
The amount of output cable compensation can be selected with
the value of the BYPASS pin capacitor. A value of 1 m F selects
the standard cable compensation. A 10 m F capacitor selects
the enhanced cable compensation. Table 2 shows the amount
of compensation for each LinkSwitch-II device and capacitor
value. The capacitor can be either ceramic or electrolytic but
tolerance and temperature variation should be ≤ ±50%.
www.powerint.com
1 m F 1.050
LNK615
10 m F 1.070
1 m F 1.060
LNK616
10 m F 1.090
Table 2. Cable Compensation Change Factor vs Device and BYPASS Pin
Capacitor Value.
The output voltage that is entered into PIXls design spreadsheet
is the voltage at the end of the output cable when the power
supply is delivering maximum power. The output voltage at the
terminals of the supply is the value measured at the end of the
cable multiplied by the output voltage change factor.
LinkSwitch-II Layout Considerations
Circuit Board Layout
LinkSwitch-II is a highly integrated power supply solution that
integrates on a single die, both, the controller and the high
voltage MOSFET. The presence of high switching currents and
voltages together with analog signals makes it especially
important to follow good PCB design practice to ensure stable
and trouble free operation of the power supply. See Figure 5 for
a recommended circuit board layout for LinkSwitch-II.
When designing a printed circuit board for the LinkSwitch-II
based power supply, it is important to follow the following
guidelines:
Single Point Grounding
Use a single point (Kelvin) connection at the negative terminal of
the input filter capacitor for the LinkSwitch-II SOURCE pin and
bias winding return. This improves surge capabilities by
returning surge currents from the bias winding directly to the
input filter capacitor.
Bypass Capacitor
The BYPASS pin capacitor should be located as close as
possible to the SOURCE and BYPASS pins.
Feedback Resistors
Place the feedback resistors directly at the FEEDBACK pin of
the LinkSwitch-II device. This minimizes noise coupling.
Thermal Considerations
The copper area connected to the SOURCE pins provides the
LinkSwitch-II heat sink. A good estimate is that the LinkSwitch-II
will dissipate 10% of the output power. Provide enough copper
area to keep the SOURCE pin temperature below 90 °C. Higher
temperatures are allowable only if an output current (CC)
tolerance above ±10% is acceptable. In this case a maximum
SOURCE pin temperature below 110 °C is recommended to
provide margin for part to part R DS(ON) variation.
5
Rev. F 01/10
相关PDF资料 |
PDF描述 |
|---|---|
| AT24C64A-10TU-2.7 | IC EEPROM 64KBIT 400KHZ 8TSSOP |
| SB3H100HE3/54 | DIODE SCHOTTKY 100V 3A AXIAL |
| IXDD414CI | IC MOSFET DRV LS 14A SGL 5TO-220 |
| DV007004 | PROGRAMMER UNIVERSAL PM3 |
| R0.25D12-1509/H-R | CONV DC/DC 0.25W 15VIN +/-9VOUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| RDK-160 | 功能描述:电源管理IC开发工具 LinkSwitch II Reference Design Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| RDK-189 | 功能描述:KIT REF DESIGN FOR PLC810 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:HiperPLC™ 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| RDK-193 | 功能描述:LED 照明开发工具 LED Drvr Ref Des LinkSwitch-PH RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| RDK-194 | 功能描述:电源管理IC开发工具 LED Drvr Ref Des LinkSwitch-PH RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| RDK-195 | 功能描述:LED 照明开发工具 RefDesign 90-265V.5A OutputLinkSwitch-PH RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
发布紧急采购，3分钟左右您将得到回复。