- 您现在的位置：买卖IC网 > PDF目录20502 > RDK-91 (Power Integrations)KIT DESIGN REF TINYSWITCH-III PDF资料下载
参数资料
| 型号： | RDK-91 |
| 厂商： | Power Integrations |
| 文件页数： | 7/35页 |
| 文件大小： | 0K |
| 描述： | KIT DESIGN REF TINYSWITCH-III |
| 标准包装： | 1 |
| 系列： | TinySwitch®-III |
| 主要目的： | AC/DC，主面 |
| 输出及类型： | 1，非隔离 |
| 功率 - 输出： | 12W |
| 输出电压： | 12V |
| 电流 - 输出： | 1A |
| 输入电压： | 85 ~ 265VAC |
| 稳压器拓扑结构： | 回扫 |
| 板类型： | 完全填充 |
| 已供物品： | 装有元件的板，裸板，样品 IC |
| 已用 IC / 零件： | TNY274，TNY275，TNY276，TNY277，TNY278，TNY279，TNY280 |
| 产品目录页面： | 1202 (CN2011-ZH PDF) |
| 相关产品： | 732-2250-ND - TRANS OFF LINE POWER PI TNY278 596-1115-6-ND - IC OFFLINE SWIT OVP OTP HV 8SMD 596-1114-6-ND - IC OFFLINE SWIT OVP OTP HV 8SMD 596-1113-6-ND - IC OFFLINE SWIT OVP OTP HV 8SMD 596-1112-6-ND - IC OFFLINE SWIT OVP OTP HV 8SMD 596-1111-6-ND - IC OFFLINE SWIT OVP OTP HV 8SMD 596-1109-6-ND - IC OFFLINE SWIT OVP OTP HV 8SMD 596-1260-5-ND - IC OFFLINE SWIT OVP OTP HV 8DIP 596-1259-5-ND - IC OFFLINE SWIT OVP OTP HV 8DIP 596-1258-5-ND - IC OFFLINE SWIT OVP OTP HV 8DIP 更多... |
| 其它名称： | 596-1194 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
11-Feb-13
RDR-91 12 V, 1 A, Universal Input Supply
4 Circuit Description
This flyback power supply was designed around the TNY278PG (U1 in Figure 2). The
output voltage is sensed and fed back to U1 through optocoupler U2. That feedback is
used by U1 to maintain constant voltage (CV) regulation of the output.
4.1 Input Rectification and Filtering
Diodes D1–D4 rectify the AC input. Capacitors C1 and C2 filter the rectified DC. Inductor
L1, C1 and C2 form a pi filter that attenuates differential mode conducted EMI.
4.2 TNY278PG Operation
The TNY278PG device (U1) integrates an oscillator, a switch controller, startup and
protection circuitry, and a power MOSFET, all on one monolithic IC.
One side of the power transformer (T1) primary winding is connected to the positive leg
of C2, and the other side is connected to the DRAIN (D) pin of U1. At the start of a
switching cycle, the controller turns the power MOSFET on, and current ramps up in the
primary winding, which stores energy in the core of the transformer. When that current
reaches the limit threshold, the controller turns the power MOSFET off. Due to the
phasing of the transformer windings and the orientation of the output diode, the stored
energy then induces a voltage across the secondary winding, which forward biases the
output diode, and the stored energy is delivered to the output capacitor. When the power
MOSFET turns off, the leakage inductance of the transformer induces a voltage spike on
the drain node. The amplitude of that spike is limited by an RCD clamp network that
consists of D5, C4 and R2. Resistor R1 and VR1 provide hard clamping of the drain
voltage, only conducting during output overload. Resistor R2 also limits the reverse
current that flows through D5 when the power MOSFET turns on. This allows a slow, low-
cost, glass passivated diode (with a recovery time of ? 2 ? s.) to be used for D5, which
improves conducted EMI and efficiency.
Using ON/OFF control, U1 skips switching cycles to regulate the output voltage, based
on feedback to its ENABLE/UNDERVOLTAGE (EN/UV) pin. The EN/UV pin current is
sampled, just prior to each switching cycle, to determine if that switching cycle should be
enabled or disabled. If the EN/UV pin current is <115 ? A, the next switching cycle begins,
and is terminated when the current through the MOSFET reaches the internal current
limit threshold. To evenly spread switching cycles, preventing group pulsing, the EN/UV
pin threshold current is modulated between 115 ? A and 60 ? A based on the state during
the previous cycle. A state-machine within the controller adjusts the MOSFET current
limit threshold to one of four levels, depending on the load being demanded from the
supply. As the load on the supply drops, the current limit threshold is reduced. This
ensures that the effective switching frequency stays above the audible range until the
transformer flux density is low. When the standard production technique of dip varnishing
is used for the transformer, audible noise is practically eliminated.
Power Integrations
Page 7 of 35
Tel: +1 408 414 9200 Fax: +1 408 414 9201
www.powerint.com
相关PDF资料 |
PDF描述 |
|---|---|
| AT25256A-10TU-1.8 | IC EEPROM 256KBIT 20MHZ 8TSSOP |
| F911C336MCC | CAP TANT 33UF 16V 20% 2312 |
| LXC100-1750SW | POWER SUPPLY LED 100W 1750MA |
| IXDD414YI | IC MOSFET DRVR LS 14A SGL 5TO263 |
| S332M33Z5UN6TJ5R | CAP CER 3300PF 1KV 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| RDK-93 | 制造商:Power Integrations 功能描述:DESIGNER KIT REFERENCE PEAKSWITCH |
| RDK-ACIM | 功能描述:开发板和工具包 - ARM AC INDUCTION MOTOR REFERENCE DESIGN KIT RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V |
| RDK-ACIM | 制造商:Texas Instruments 功能描述:Stellaris AC Induction Motor Reference D 制造商:Texas Instruments 功能描述:STELLARIS, LM3S818, AC INDUCTION MOTOR, RDK |
| RDK-AVIIA-HD00 | 制造商:Gennum Corporation 功能描述:RDK-AVIIA-HD00 |
| RDK-BDC | 功能描述:电源管理IC开发工具 BRUSHED DC MOTOR CONTROL REF DESIGN RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。