- 您现在的位置：买卖IC网 > PDF目录21887 > RE46C180E16F (Microchip Technology)IC ION SMOKE DETECT ASIC 16PDIP PDF资料下载
参数资料
| 型号： | RE46C180E16F |
| 厂商： | Microchip Technology |
| 文件页数： | 19/58页 |
| 文件大小： | 851K |
| 描述： | IC ION SMOKE DETECT ASIC 16PDIP |
| 标准包装： | 25 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页
?2011 Microchip Technology Inc.
DS22275A-page 19
RE46C180
FIGURE 4-1:
Nominal Application Circuit for Programming.
4.2
Smoke Calibration
A separate calibration mode is entered for each mea-
surement mode (Normal, Hysteresis, HUSH and
PTT/Chamber Test) so that independent limits can be
set for each.
In all calibration modes the V
SEN
voltage, which repre-
sents the smoke sensitivity level, can be accessed at
T3 output. The SmkCompOut output voltage is the
result of the comparison of DETECT and V
SEN
, and
can be accessed at TESTOUT output. The FEED input
can be clocked to cycle through the available smoke
sensitivity levels. Once the desired smoke sensitivity
level is reached, the IO input is pulsed low to high to
store the result.
The detailed procedure is described in the following
steps:
1. Power up with the bias condition shown in
Figure 4-1. At power-up:
TEST = IO = FEED = T2 = V
SS
,
DETECT = V
DD
. Now in mode M0.
2. Drive T2 input from V
SS
to V
DD
and hold at V
DD
to enter TM0.
3. Drive TEST from V
SS
to V
DD
and hold at V
DD
.
4. Apply four clock pulses to the T2 input (V
DD
to
V
SS
and back to V
DD
) to enter in TM4 mode.
This initiates the Calibration mode for the normal
sensitivity setting. Drive TEST from V
DD
to V
SS
to turn on the smoke comparator and enable the
T3 switch. The standby smoke sensitivity V
SEN
will appear at T3. The smoke comparator output
will appear at TESTOUT. Clock FEED to
increase or decrease the V
SEN
levels as
needed. The IO input is pulsed low-to-high to
save the result.
5. Drive TEST from V
SS
to V
DD
and hold at V
DD
.
Apply another clock pulse to the T2 input, to
enter in TM5 mode. This initiates the Calibration
mode for the hysteresis setting. Drive TEST
from V
DD
to V
SS
to turn on the smoke compara-
tor and enable the T3 switch. The local alarm
smoke sensitivity V
SEN
will appear at T3. The
smoke comparator output will appear at TES-
TOUT. Clock FEED to increase or decrease the
V
SEN
levels as needed. The IO input is pulsed
low-to-high to save the result.
V
Battery
+
-
R1
1
k
TEST
IO
GLED
CHAMBER
RLED
DD
TESTOUT
FEED
GUARD2
DETECT
T3
T2
HS
HB
VSS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
RE46C180
R2
1
k
V1
V2 V3 V4
V5
V6
Monitor TESTOUT,
T3 and CHAMBER
GUARD1
V
相关PDF资料 |
PDF描述 |
|---|---|
| MLBAWT-H1-0000-000UA7 | XLAMP MLB SERIES LED WHITE |
| MLBAWT-H1-0000-000UA6 | XLAMP MLB SERIES LED WHITE |
| MLBAWT-H1-0000-000UA5 | XLAMP MLB SERIES LED WHITE |
| TSL2569CS | IC LIGHT TO DGTL CONV 6CHIPSCALE |
| MLEAWT-A1-0000-0001E7 | LED XLAMP WARM WHITE 3000K SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| RE46C180S16F | 功能描述:烟雾报警器 E-CAL ION S.D. RoHS:否 制造商:ELMOS Semiconductor 描述/功能:Smoke detector controller 感应方式:Photoelectric 工作电源电压:24 V 输出信号类型: |
| RE46C180S16TF | 功能描述:烟雾报警器 E-CAL ION S.D. RoHS:否 制造商:ELMOS Semiconductor 描述/功能:Smoke detector controller 感应方式:Photoelectric 工作电源电压:24 V 输出信号类型: |
| RE46C190 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:CMOS Low Voltage Photoelectric Smoke Detector ASIC with Interconnect |
| RE46C190S16F | 功能描述:烟雾报警器 3V E-Cal Photo S.D. IC RoHS:否 制造商:ELMOS Semiconductor 描述/功能:Smoke detector controller 感应方式:Photoelectric 工作电源电压:24 V 输出信号类型: |
| RE46C190S16F | 制造商:Microchip Technology Inc 功能描述:3V E-Cal Photo S.D. IC 16 SOIC .150in TU 制造商:Microchip Technology Inc 功能描述:IC, CMOS SMOKE DETECTOR, 5V, 1UA, SOIC-16 |
发布紧急采购，3分钟左右您将得到回复。