- 您现在的位置：买卖IC网 > PDF目录18762 > RN42-I/RM (Microchip Technology)MODULE BLUETOOTH V2.1+EDR PDF资料下载
参数资料
| 型号： | RN42-I/RM |
| 厂商： | Microchip Technology |
| 文件页数： | 8/12页 |
| 文件大小： | 0K |
| 描述： | MODULE BLUETOOTH V2.1+EDR |
| 应用说明： | Cable Replacement |
| 产品变化通告： | Mfg/Part Number Change 20/Jun/2012 |
| 标准包装： | 1 |
| 系列： | RN |
| 频率： | 2.4GHz |
| 数据传输率 - 最大： | 3Mbps |
| 调制或协议： | Bluetooth v2.1+EDR，2类和 3类 |
| 应用： | 通用 |
| 功率 - 输出： | 2dBm |
| 灵敏度： | -80dBm |
| 电源电压： | 3 V ~ 3.6 V |
| 电流 - 接收： | 25mA |
| 电流 - 传输： | 25mA |
| 数据接口： | PCB，表面贴装 |
| 天线连接器： | 板载，芯片 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 封装设备 |
| 包装： | 标准包装 |
| 其它名称： | 740-1038-6 |
RN -42 -DS
?
In this mode, the Bluetooth stack is no longer on-board the module. It is offloaded to the interfacing host processor. The
Bluetooth module is used as a radio, performing the lower level MAC functionalities, while the application stack runs on the
host processor.
Using the module in HCI mode allows designers to implement profiles that are not natively supported on the Bluetooth
module.
NOTE: HCI mode requires a separate firmware build that must be loaded into the module’s flash at the factory. Is not
upgradeable in the field.
Roving Networks offers HCI mode in two hardware interfaces:
?
?
HCI over UART
HCI over USB
HCI over UART
In this mode, the hardware interface between the host processor and the Bluetooth module is the UART. You must
interface the flow control signals between the host processor and the Bluetooth module for the HCI interface to work.
Failure to do so can cause the host processor and the Bluetooth module to become out of sync and break the Bluetooth
link.
HCI over USB
In this mode, the hardware interface between the host processor and the Bluetooth module is the USB. In this
architecture, the Bluetooth module is the USB slave and the host processor is the USB host.
Using the USB interface offers the advantage of a faster data link between the Bluetooth module and the host processor.
With this architecture, it is possible to achieve Bluetooth’s theoretical maximum throughput of 3 Mpbs.
Low Power
To achieve low-power operation, hold the module’s RESET pin low. With RESET = 0 VDC, the module consumes 35 uA of
power. If RESET is left floating or high, the module consumes 3 mA in sleep mode. To obtain the lowest power, the RN-42
should be passive (in slave mode and not trying to make connections).
Using the SPI Bus to Upgrade the Flash Memory
While not required, this bus is very useful for configuring the Bluetooth modules’ advanced parameters. The bus is
required when upgrading the module’s firmware. The typical application schematic shown in Figure 4 shows a 6-pin
header that can be implemented to gain access to this bus. A minimum-mode version might simply use the SPI signals (4
pins) and obtain ground and VCC from elsewhere in the design.
Minimizing Radio Interference
When laying out the carrier board for the RN-42 module, the areas under the antenna and shielding connections should
not have surface traces, ground planes, or exposed vias (see Figure 5). For optimal radio performance, the RN-42
module’s antenna end should protrude at least 5 mm beyond any metal enclosure.
www.rovingnetworks.com
Version 2.2r 4/9/2012
8
相关PDF资料 |
PDF描述 |
|---|---|
| ST-6-36 | XFRMR PWR 115V 18VAC 1.1A |
| ST-6-24 | XFRMR PWR 115V 12VAC 1.6A |
| ST-6-12 | XFRMR PWR 115V 6.3VAC 3.2A |
| PC-56-420 | XFRMR PWR 115V 28V 840MA 24VA |
| PC-120-200 | XFRMR PWR 115V 60V 400MA 24VA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| RN-42-N | 制造商:Roving Networks 功能描述:BLUETOOTH MODULE |
| RN42NHCI-I/RM | 制造商:Microchip Technology 功能描述:Bluetooth Class II 3Mbps 35-Pin SMD Tray 制造商:Microchip Technology Inc 功能描述:BLUETOOTH 2.1 CLASS 2 SURFACE MOUNT MOD W/O ANT W/HCI H4 OVE - Bag 制造商:Microchip Technology Inc 功能描述:MODULE BLUETOOTH 2.1 HCI C2 UART |
| RN42NHID-I/RM | 制造商:Microchip Technology 功能描述:Bluetooth Class II 3Mbps 35-Pin SMD Tray 制造商:Microchip Technology Inc 功能描述:BLUETOOTH 2.1 CLASS 2 SURFACE MOUNT MOD W/O ANT W/HUMAN INT - Bag 制造商:Microchip Technology Inc 功能描述:MODULE BLUETOOTH 2.1 W/HID C2 |
| RN42N-I/RM | 功能描述:蓝牙/802.15.1 模块 Class2 Bluetooth Mod v2.0+EDR w/o Antenna RoHS:否 制造商:Murata Wireless Solutions 类:1 频带:2402 MHz to 2480 MHz 灵敏度:- 92 dBm 数据速率: 工作电源电压:2.2 V to 3.3 V 输出功率: 接口类型:PCM, UART 天线连接器类型:Chip 最大工作温度:+ 85 C 尺寸:17.5 mm x 16 mm x 2 mm |
| RN42NU-I/RM | 功能描述:蓝牙/802.15.1 模块 Class2 Bluetooth mod no ant, HCI over USB RoHS:否 制造商:Murata Wireless Solutions 类:1 频带:2402 MHz to 2480 MHz 灵敏度:- 92 dBm 数据速率: 工作电源电压:2.2 V to 3.3 V 输出功率: 接口类型:PCM, UART 天线连接器类型:Chip 最大工作温度:+ 85 C 尺寸:17.5 mm x 16 mm x 2 mm |
发布紧急采购，3分钟左右您将得到回复。