- 您现在的位置：买卖IC网 > Datasheet目录877 > RNE0J271MDS1 (Nichicon)CAP ALUM 270UF 6.3V 20% RADIAL Datasheet资料下载
参数资料
| 型号： | RNE0J271MDS1 |
| 厂商： | Nichicon |
| 文件页数： | 6/60页 |
| 文件大小： | 0K |
| 描述： | CAP ALUM 270UF 6.3V 20% RADIAL |
| 标准包装： | 2,000 |
| 系列： | NE |
| 电容： | 270µF |
| 额定电压： | 6.3V |
| 容差： | ±20% |
| 寿命@温度： | 105°C 时为 2000 小时 |
| 工作温度： | -55°C ~ 105°C |
| 特点： | 聚合物 |
| 纹波电流： | 5.6A |
| ESR（等效串联电阻）： | 11 毫欧 |
| 安装类型： | 通孔 |
| 封装/外壳： | 径向，Can |
| 尺寸/尺寸： | 0.197" 直径（5.00mm） |
| 高度 - 座高（最大）： | 0.354"（9.00mm） |
| 引线间隔： | 0.079"（2.00mm） |
| 包装： | 散装 |
| 其它名称： | 493-6622 |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页
Precautions
(7) Handling after soldering
a) Do not tilt, bend or twist the FPCAP after it has been soldered on the PC board.
b) Do not use the FPCAP as a handle to move the PC board after it has been attached to it.
c) Do not bump the FPCAP with objects after it has been soldered to the PC board. Make sure the FPCAP does not touch
other PC boards or components.
d) Do not subject to excessive stress after it has been soldered to the PC board.
(8) Washing the PC board
Check the following items before washing the PC board with these detergents; high quality alcohol-based cleaning fluid such as
Pine- α ST-100S, Clean-thru 750H, 750L, 750K, or Techno Care FRW14 through 17; or detergents including substitute
Freon such as AK-225AES and IPA.
a) Use immersion or ultrasonic wave to clean for a total of less than five minutes.
b) The temperature of the cleaning fluid should be less than 60 ° C.
c) Watch for contamination of the detergent (conductivity, pH, specific gravity, water content, etc.).
d) After cleaning do not store in a location subject to gases from the cleaning fluid or in an airtight container.
Dry the PC board and the FPCAP using hot air (less than the maximum operating temperature).
e) Please contact our company for details about detergents and cleaning methods, and about detergents other than those
listed above.
(9) Fixatives and coatings
a) Select appropriate material for the FPCAP marking material and sealant.
In particular, make sure the fixative, coating and thinner do not contain acetone or toluene.
b) Before applying a fixative or coating, completely remove any flux residue and foreign matter from the area where the PC board
and the FPCAP are to be joined together.
c) Allow any detergent to dry before applying the fixative or coating.
d) Please contact our company for fixative and coating heat curing conditions.
3. Precautions with completed board
(1) Do not directly touch the FPCAP terminals.
(2) Do not use electric conductors to cause a short circuit between the FPCAP terminals.
Do not subject the FPCAP to conductive solutions.
(3) Check the installation environment of the board on which the FPCAP is mounted.
(4) Aging of the completed board, please use the voltage below the rated voltage of the capacitor.
(5) It is recommended that the board be used at room temperature and in ordinary humidity.
For details, refer to the Operating Precaution Guidelines for the EIAJ RCR-2367C. (Safety Application Guide for fixed
aluminum electrolytic capacitors for use in electronic equipment.)
No part of this publication shall be reproduced without prior written permission of the publisher.
4. If trouble should occur
(1) In the event that a short circuit causes the current to become relatively small (Radial lead type : less than approximately
3A for φ 10 and less than approximately 1A for φ 6.3), the FPCAP itself will generate some heat, but the appearance
will not be affected even when electricity is supplied continuously. However, if there is a short circuit and the current value
exceeds the above mentioned values, the temperature inside the FPCAP will increase.
When the temperature exceeds approximately 200 ° C the internal pressure will increase, and an odorous gas will be released.
In this case, do not allow contact with your face and hands.
(2) If a short circuit occurs and an odorous gas is released, either turn off the device’s main power or unplug the power cord from
the outlet.
(3) If a short circuit should occur, it may take anywhere from a few seconds to a few minutes until an odorous gas develops,
depending on the conditions. Design the device so that a power protection circuit works during this time period.
4
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
相关PDF资料 |
PDF描述 |
|---|---|
| RNE1C101MDS1PX | CAP ALUM 100UF 16V 20% RADIAL |
| RNM-3.315S | CONV DC/DC 1W 3.3VIN 15VOUT |
| RNS03ZE-M6G | CONV DC-DC 48V IN 3.3V OUT 10W |
| RNS1E101MDN1PH | CAP ALUM 100UF 25V 20% RADIAL |
| RNU0J221MDN1JX | CAP ALUM 220UF 6.3V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| RNE1/4-100K | 制造商:Misc 功能描述: |
| RNE1/4-124R | 制造商:Misc 功能描述: |
| RNE1/4-20K0 | 制造商:Misc 功能描述: |
| RNE1/4-221R | 制造商:Misc 功能描述: |
| RNE1/4-249K | 制造商:Misc 功能描述: |
发布紧急采购，3分钟左右您将得到回复。