- 您现在的位置：买卖IC网 > PDF目录15181 > RNU1E331MDN1PH (Nichicon)CAP ALUM 330UF 25V 20% RADIAL PDF资料下载
参数资料
| 型号： | RNU1E331MDN1PH |
| 厂商： | Nichicon |
| 文件页数： | 5/60页 |
| 文件大小： | 0K |
| 描述： | CAP ALUM 330UF 25V 20% RADIAL |
| 标准包装： | 1 |
| 系列： | NU |
| 电容： | 330µF |
| 额定电压： | 25V |
| 容差： | ±20% |
| 寿命@温度： | 105°C 时为 2000 小时 |
| 工作温度： | -55°C ~ 105°C |
| 特点： | 聚合物 |
| 纹波电流： | 5A |
| ESR（等效串联电阻）： | 14 毫欧 |
| 安装类型： | 通孔 |
| 封装/外壳： | 径向，Can |
| 尺寸/尺寸： | 0.394" 直径（10.00mm） |
| 高度 - 座高（最大）： | 0.551"（14.00mm） |
| 引线间隔： | 0.197"（5.00mm） |
| 包装： | 剪切带 (CT) |
| 其它名称： | 493-6635-1 |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页
Precautions
2. Mounting precautions
(1) Things to know before mounting
a) Do not reuse the FPCAP that has already been assembled in a device and energized.
Excluding the FPCAP that has been removed for measuring electrical characteristics during a periodic inspection,
they cannot be reused.
b) Leakage current may increase if the part has been stored for a long period of time.
In this case, use after voltage treatment under the rated voltage.
(2) Mounting-1
a) Mount after checking the capacitance and the rated voltage.
b) Mount after checking the polarity.
c) Do not drop on the floor and do not use parts that have been dropped.
d) Do not deform and then mount.
(3) Mounting-2
a) Mount after checking the match between the lead pitch and the PC board holes pitch.
b) When an automatic insertion equipment is used to clinch the lead wires, make sure it is set correctly.
c) Be careful of the shock force that can be produced by the automatic insertion equipment.
d) Do not apply excessive external force to the lead wires, the FPCAP itself, or the electrode terminals.
(4) Soldering with a soldering iron
a) Set the soldering conditions (temperature, time) so that they fall within the range stipulated by the catalog specification.
b) When the lead wire terminal must be processed because the terminal spacing and the PC board holes spacing do not match,
process it before soldering so that no stress is applied to the FPCAP itself.
c) Do not subject the FPCAP itself to excessive stress when soldering with a soldering iron.
d) When a soldering iron is used to repair the FPCAP that has already been soldered once and needs to be removed,
do it after the solder has been completely melted so that no stress is applied to the FPCAP terminals.
e) Do not let the tip of the soldering iron touch the FPCAP itself.
f ) The amount of leakage current after soldering may increase a slightly (from a few μ A to several hundred μ A) depending
on the soldering condition (preheating and solder temperature and time, PC board material and thickness, etc.)
The leakage current can be reduced by applying voltage.
(5) Flow soldering (Radial lead type)
a) Never submerge the FPCAP in molten solder. Use the PC board to protect the FPCAP and only solder the opposite side
of the board that the FPCAP is mounted on.
b) Set the soldering conditions (soldering temperature, terminal submersion time) so that they fall within the range stipulated
by the catalog specification. The amount of leakage current after soldering may increase slightly (from a few μ A to several
hundred μ A) depending on the soldering conditions (preheating and solder temperature and time, PC board material and
thickness, etc.). The leakage current can be reduced through self-repair by applying voltage.
c) Take care that flux does not adhere to any place other than the terminals.
d) When soldering, take care that other components do not fall over and touch the FPCAP.
e) Flow soldering under extremely abnormal conditions may reduce the capacitance of products before or after soldering.
(6) Reflow soldering (SMD type)
Do not use reflow soldering for Radial lead type (Through Hole).
a) Never submerge the FPCAP in molten solder. Use the PC board to protect the FPCAP and only solder the opposite side
of the board that the FPCAP is mounted on.
b) Set the soldering conditions (soldering temperature, terminal submersion time) so that they fall within the range stipulated
by the catalog specification. The amount of leakage current after soldering may increase slightly (from a few μ A to several
hundred μ A) depending on the soldering conditions (preheating and solder temperature and time, PC board material and
thickness, etc.). The leakage current can be reduced through self-repair by applying voltage.
c) Take care that flux does not adhere to any place other than the terminals.
d) When soldering, take care that other components do not fall over and touch the FPCAP .
e) Reflow soldering under extremely abnormal conditions may reduce the capacitance of products before or after soldering.
f) Do not use VPS (Vapor Phase Soldering).
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
3
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B42-EV-F2 | CONVERTER MOD DC/DC 15V 150W |
| B41042A4228M | 2200UF 16V 12.5X31.5 SINGLE END |
| CAT1161WI-45-GT3 | IC SUPERVSR CPU 16K EEPROM 8SOIC |
| ISL6744AUZ | IC REG CTRLR BUCK PWM VM 8-MSOP |
| ESC22DRYS | CONN EDGECARD 44POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| RNU1E331MDNASQ | 功能描述:CAP ALUM POLY 330UF 20% 25V T/H 制造商:nichicon 系列:FPCAP，RNU 包装:散装 零件状态:在售 类型:聚合物 电容:330μF 容差:±20% 电压 - 额定:25V ESR（等效串联电阻）:14 毫欧 不同温度时的使用寿命:105°C 时为 2000 小时 工作温度:-55°C ~ 105°C 等级:- 应用:通用 Ripple Current:500mA @ 120Hz Ripple Current @ High Frequency:5A @ 100kHz 引线间距:0.197"（5.00mm） 大小/尺寸:0.394" 直径（10.00mm） 高度 - 安装（最大值）:0.551"（14.00mm） 表面贴装焊盘尺寸:- 安装类型:通孔 封装/外壳:径向，Can 标准包装:100 |
| RNU1E331MDNASQPH | 功能描述:CAP ALUM POLY 330UF 20% 25V T/H 制造商:nichicon 系列:FPCAP，RNU 包装:剪切带（CT） 零件状态:在售 类型:聚合物 电容:330μF 容差:±20% 电压 - 额定:25V ESR（等效串联电阻）:14 毫欧 不同温度时的使用寿命:105°C 时为 2000 小时 工作温度:-55°C ~ 105°C 等级:- 应用:通用 Ripple Current:500mA @ 120Hz Ripple Current @ High Frequency:5A @ 100kHz 引线间距:0.197"（5.00mm） 大小/尺寸:0.394" 直径（10.00mm） 高度 - 安装（最大值）:0.551"（14.00mm） 表面贴装焊盘尺寸:- 安装类型:通孔 封装/外壳:径向，Can 标准包装:1 |
| RNU1E391MDN1PH | 功能描述:390μF 25V Aluminum - Polymer Capacitors Radial, Can 14 mOhm 2000 Hrs @ 105°C 制造商:nichicon 系列:FPCAP，RNU 包装:剪切带（CT） 零件状态:有效 电容:390μF 容差:±20% 额定电压:25V ESR（等效串联电阻）:14 毫欧 不同温度时的使用寿命:105°C 时为 2000 小时 工作温度:-55°C ~ 105°C 极化:极化 应用:通用 纹波电流:5A 阻抗:- 引线间距:0.197"（5.00mm） 大小/尺寸:0.394" 直径（10.00mm） 高度 - 安装（最大值）:0.551"（14.00mm） 表面贴装焊盘尺寸:- 安装类型:通孔 封装/外壳:径向，Can 标准包装:1 |
| RNU1E391MDNASQ | 功能描述:CAP ALUM POLY 390UF 20% 25V T/H 制造商:nichicon 系列:FPCAP，RNU 包装:散装 零件状态:在售 类型:聚合物 电容:390μF 容差:±20% 电压 - 额定:25V ESR（等效串联电阻）:14 毫欧 不同温度时的使用寿命:105°C 时为 2000 小时 工作温度:-55°C ~ 105°C 等级:- 应用:通用 Ripple Current:500mA @ 120Hz Ripple Current @ High Frequency:5A @ 100kHz 引线间距:0.197"（5.00mm） 大小/尺寸:0.394" 直径（10.00mm） 高度 - 安装（最大值）:0.551"（14.00mm） 表面贴装焊盘尺寸:- 安装类型:通孔 封装/外壳:径向，Can 标准包装:100 |
| RNU1E391MDNASQPH | 功能描述:CAP ALUM POLY 390UF 20% 25V T/H 制造商:nichicon 系列:FPCAP，RNU 包装:剪切带（CT） 零件状态:在售 类型:聚合物 电容:390μF 容差:±20% 电压 - 额定:25V ESR（等效串联电阻）:14 毫欧 不同温度时的使用寿命:105°C 时为 2000 小时 工作温度:-55°C ~ 105°C 等级:- 应用:通用 Ripple Current:500mA @ 120Hz Ripple Current @ High Frequency:5A @ 100kHz 引线间距:0.197"（5.00mm） 大小/尺寸:0.394" 直径（10.00mm） 高度 - 安装（最大值）:0.551"（14.00mm） 表面贴装焊盘尺寸:- 安装类型:通孔 封装/外壳:径向，Can 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。