- 您现在的位置：买卖IC网 > PDF目录243306 > RP-21002D0-380W (DATA DEVICE CORP) SPECIALTY ANALOG CIRCUIT, DMA10 PDF资料下载
参数资料
| 型号： | RP-21002D0-380W |
| 厂商： | DATA DEVICE CORP |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, DMA10 |
| 封装： | DIP-10 |
| 文件页数： | 11/12页 |
| 文件大小： | 135K |
| 代理商： | RP-21002D0-380W |
8
Data Device Corporation
www.ddc-web.com
RP-21000 Series
H-04/03-0
The Power MOSFETs have the opposite characteristics from
that of thermal runaway in bipolar devices. A local hot-spot will
steer current away from itself as its resistance in this area goes
up. This results in even current sharing throughout the entire
device, thereby eliminating hot-spots. The inherent advantage of
not having secondary breakdown is that the entire MOSFET has
to exceed its temperature limitations before damage results. This
characteristic makes the Power MOSFET more rugged when
used for power switching then bipolar devices.
Due to the current sharing aspects of the power MOSFET, they
can be placed in parallel and share the load equally. DDC has a
standard 28 Vdc 80 AMP power module which uses this tech-
nique.
ISOLATION OF CONTROL AND STATUS
The SSPC was designed with isolation between the load power
and the five volt control logic input and the status outputs. This is
necessary to prevent noise caused by transients or power spikes
on the power line from adversely affecting the operation of the
SSPC. Therefore the case, POWER IN, and Control Circuit are
all electrically isolated. FIGURE 1 shows this isolation as the
"ISOLATED CONTROL CIRCUIT."
SSPC failure or Status 2 shorted to ground
LOW
HIGH
LOW
Load is “OFF”, Normal Condition
HIGH
LOW
SSPC failure or Status 2 shorted to ground
LOW
HIGH
Load is “ON”, Normal Condition
HIGH
LOW
HIGH
Load is “OFF”, Tripped
LOW
HIGH
Load is “ON”, Load < 5.0% Rated Current
HIGH
SSPC failure or Status1 shorted to ground
HIGH
LOW
SSPC failure, or Status1 and Status 2 short-
ed to ground, or No Bias
LOW
SYSTEM STATUS
STATUS 2
LOW
STATUS 1
Status 1 indicates a logic LOW if > 15% of the rated current is flowing.
Status 2 indicates a logic LOW if the SSPC is tripped due to overcurrent.
The electrical isolation is supported by an internal power oscilla-
tor that electrically isolates separate internal power supplies that
will power the internal analog and digital monolithics. This isola-
tion prevents load or logic ground loops from affecting the prop-
er operation of the SSPC. The isolation also insures that a fault
of the switch (MOSFET) could never propagate back into the
SSPC logic or cause damage to the logic side.
OPTIONS
The Following characteristics can be factory modified on special
orders:
I2T TRIP CURVE: K-factor adjustments
OUTPUT RISE AND FALL TIMES: Turn-off and Turn-on times
can be factory modified (e.g., capacitive loads)
CURRENT RANGE
POWER-ON RESET: Other options are available
INPUT CONTROL:
TTL or CMOS or Both with Hysteresis (Schmitt trigger char-
acteristics)
CUSTOM PACKAGING
OPTIONAL STATUS TRUTH TABLE (See TABLE 6)
LOW
CONTROL
TABLE 6. OPTIONAL STATUS TRUTH TABLE
相关PDF资料 |
PDF描述 |
|---|---|
| RP-21002D0-570K | SPECIALTY ANALOG CIRCUIT, DMA10 |
| RP-21002D0-820Z | SPECIALTY ANALOG CIRCUIT, DMA10 |
| RP-21002D0-870Y | SPECIALTY ANALOG CIRCUIT, DMA10 |
| R1221N15XF-TR-FA | SWITCHING CONTROLLER, PDSO6 |
| R1221N20XD-TR-FA | SWITCHING CONTROLLER, PDSO6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| RP-21002D1-100 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Electronic Circuit Breaker |
| RP-21002D1-110 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Electronic Circuit Breaker |
| RP-21002D1-120 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Electronic Circuit Breaker |
| RP-21002D1-200 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Electronic Circuit Breaker |
| RP-21002D1-300 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Electronic Circuit Breaker |
发布紧急采购，3分钟左右您将得到回复。