- 您现在的位置：买卖IC网 > Datasheet目录990 > RP15-4812SA (RECOM Power)DC/DC转换器 15W DC/DC 1.6kV REG 36-75Vin 12Vout Datasheet资料下载
Model
No.
MP915
MP916
MP925
MP930
MP9100
Package
TO-126 Style
TO-220 Style
TO-220 Style
TO-220 Style
TO-247 Style
Resistance
Min. Max.
0.020 ? 1.00 K
0.010 ? 0.019 ?
5.00 K 100 K
0.020 ? 4.99 K
0.050 ? 100 ?
Power
Rating
15 Watts *
16 Watts *
25 Watts *
30 Watts *
100 Watts *
Max.
Voltage
200
Power
Limited
500
250
Power
Limited
Thermal Resistance
R θ JC
Film ( J ) to Case ( C )
8.33 ° C/Watt
7.81 ° C/Watt
5.00 ° C/Watt
4.17 ° C/Watt
1.50 ° C/Watt
Max. Temp.
T MAX
150 ° C
150 ° C
150 ° C
150 ° C
175 ° C
Dimensions
Figure 1
Figure 2
Figure 2
Figure 2
Figure 3
Page 2 of 2
Comments
Ceramic mounting surface
Ceramic mounting surface
Ceramic mounting surface
Ceramic mounting surface
Ceramic mounting surface
B
Derating Curve
100
80
60
40
A
20
0
25 100 150 175
CASE TEMPERATURE, ° C
A - MP915, MP916, MP925, MP930 Max. Temperature, T Max = 150 ° C
* Derating Using Case Temperature (TC):
All power and associated overload ratings are derated
based upon case temperature using the derating curve.
The case temperature is measured at the center of the
ceramic mounting surface, with the part properly
mounted and under electrical load. Without a heat sink,
when in free air at +25°C, the MP915 is rated for 1.25
watts, the MP916, MP925, MP930 are rated for 2.25
watts, and the MP9100 is rated for 3.5 watts.
Speci?cations:
Temperature Coef?cient for MP915, MP916,
MP925, and MP930:
TC referenced to +25°C, Δ R taken at +150°C
0.50 ohms and above, -20 to +80 ppm/°C
0.050 ohm to 0.49 ohms, 0 to +200 ppm/°C
0.020 ohm to 0.049 ohm, 0 to +300 ppm/°C
0.010 ohm to 0.019 ohm, 0 to +500 ppm/°C
B - MP9100 Max. Temperature, T Max = 175 ° C
The thermal design should satisfy the following equation:
Case Temperature (Tc ) + [Thermal Resistance (R θ JC) x power applied (Watts)] ≤ T MAX considering the full
operating temperature range of the application.
Mounting Note: Mount on a smooth, clean, and ?at heat sink surface with a thermal interface material, such
as thermal grease. The entire exposed ceramic portion must be in thermal contact with the heat sink. When
screw mounting, use a compression washer which provides a mounting force of 150 to 300 pounds (665 to
1330 N). This will provide suf?cient pressure on the package over time and through large temperature varia-
tions to maintain the maximum power dissipation capability. Mounting torque to avoid package damage is 8
in-lbs. (0.90 N-m). If a spring clip is used, a clip force of 8 to 30 pounds (35 to 130 N) is recommended to be
applied to the center of the package. The clip should be round or smooth in the contact area to avoid concen-
trating the load on a small point of the plastic body of the package. Another mounting option is to use a
pressure bar method which can achieve a greater mounting force with a greater contact area.
For additional applications information regarding mounting and pulse handling see the Caddock
Applications Notes at caddock.com or contact Applications Engineering.
.094 ± .004 .320 ± .010 .110 ± .010
(2.39 ± .10) DIA. ( 8.1 2 ± .26 ) (2.79 ± .26)
CL
Temperature Coef?cient for MP9100:
TC referenced to +25°C, Δ R taken at +175°C
0.50 ohms and above, -20 to +80 ppm/°C
0.050 ohm to 0.49 ohms, 0 to +150 ppm/°C
Operating Temperature: -55°C to T MAX
Inductance: MP915, MP916, MP925, and MP930
10nH typical; MP9100, 20nH typical, in series when
measured at a point 0.2 inches from the resistor
body.
DWV: The dielectric strength rating of 1500 V rms AC
is based upon connections made between
terminals shorted, and the metal surface the part is
mounted to or a metal clip in contact with the top
surface of the part.
Figure 1
TO-126 Style
MP915
Figure 2
TO-220 Style
MP916, MP925
and MP930
.080 ± .020
(2.03 ± .51)
.450 ± .050
(11.43 ± 1.27)
.125 ± .004
(3.18 ± .10) DIA.
.130 ± .030
(3.30 ± .76)
.500 ± .050
(12.70 ± 1.27)
+
MP915
0.10 ?
1%
.410 ± .010
(10.41 ± .26)
CL
MP930
10.0
1%
.115 ± .010
(2.92 ± .26)
.053 ± .007
(1.35 ± .18)
.030 ± .004
(.76 ± .10)
.200 ± .010
(5.08 ± .26)
.125 ± .010
(3.18 ± .26)
.053 ± .007
(1.35 ± .18)
.030 ± .004
(.76 ± .10)
.440 ± .010
(11.18 ± .26)
.025 ± .004 (.64 ± .10)
.058 ± .007 (1.47 ± .18)
.125 ± .010
(3.18 ± .26)
.640 ± .010
(16.26 ± .26)
Insulation Resistance: 10,000 Megohms min.
The resistor element is electrically isolated from
the mounting surface.
Load Stability: 2,000 hours at rated power.
Δ R ±(1.0 percent + 0.0005 ohm) max. Power
rating dependent upon case temperature. See
derating curve.
Momentary Overload: 1.5 times rated power with
applied voltage not to exceed 1.5 times maximum
continuous operating voltage for 5 seconds. Δ R
±(0.5 percent + 0.0005 ohm) max.
Moisture Resistance: Mil-Std-202, Method 106.
Δ R ±(0.5 percent + 0.0005 ohm) max.
Thermal Shock: Mil-Std-202, Method 107, Cond. F.
Δ R ±(0.5 percent + 0.0005 ohm) max.
0.143 ± 0.004
(3.63 ± 0.10) Dia.
Figure 3
(2.79 0.76)
TO-247 Style 0.110 ± 0.030
MP9100
0.570 ± 0.050
(14.48 ± 1.27)
DIMENSIONS IN INCHES AND (MILLIMETERS)
0.620 ± 0.010
(15.75 ± 0.26)
CL
MP 9100
50.0
1%
.200 ± .010
(5.08 ± .26)
0.210 ± 0.010
(5.33 ± 0.26)
0.143 ± 0.007
(3.63 ± 0.18)
0.060 ± 0.004
(1.52 ± 0.10)
0.400 ± 0.010
(10.16 ± 0.26)
.025 ± .004 (.64 ± .10)
.070 ± .010 (1.78 ± .26)
0.195 ± 0.010
(4.95 ± 0.26)
0.815 ± 0.010
(20.70 ± 0.26)
0.032 +0.004 / -0.010
(0.81 +0.10 / -0.26)
0.095 ± 0.010
(2.41 ± 0.26)
Shock: 100G, Mil-Std-202, Method 213, Cond. I.
Δ R ±(0.4 percent + 0.0005 ohm) max.
Vibration, High Frequency: Mil-Std-202, Method
204, Cond. D. Δ R ±(0.4 percent + 0.0005 ohm)
max.
Terminal Strength: Mil-Std-202, Method 211,
Cond. A (Pull Test) 5 lbs. Δ R ±(0.2 percent
+ 0.0005 ohm) max.
Terminal Material: Solderable
Measurement Note: For these specifications,
resistance measurement shall be made at a point
0.2 inch (5.08 mm) from the resistor body.
Applications Engineering
17271 North Umpqua Hwy.
Roseburg, Oregon 97470-9422
Phone: (541) 496-0700
Fax: (541) 496-0408
? 2004 Caddock Electronics, Inc.
e-mail: DOCK
CAD caddock@caddock.com ? web: www.caddock.com
For Caddock Distributors listed by country see caddock.com/contact/dist.html
Sales and Corporate Of?ce
1717 Chicago Avenue
Riverside, California 92507-2364
Phone: (951) 788-1700
Fax: (951) 369-1151
28_IL102.1004
相关PDF资料 |
PDF描述 |
|---|---|
| MPF480D4 | RELAY SOLID STATE PCB MOUNT |
| MPR5JB30L0 | RES .03 OHM 5W 5% RADIAL |
| MPX240D5R | RELAY,SOLID STATE, 5A, 4-SIP |
| MRF03-2X6P-1.27-400 | CABLE ASSEMBLY 6 COND 400MM |
| MRJ0150DD-A | C/A MRJ21/MRJ21 GBE STRT CMR 15M |
相关代理商/技术参数 |
参数描述 |
|---|---|
| RP15-4812SA/N | 功能描述:DC/DC转换器 15W DC/DC 1.6kV REG 36-75Vin 12Vout RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| RP15-4812SA/N-HC | 功能描述:DC/DC转换器 15W DC/DC 1.6kV REG 36-75Vin 12Vout RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| RP15-4812SA/P | 功能描述:DC/DC转换器 15W DC/DC 1.6kV REG 36-75Vin 12Vout RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| RP15-4812SA/P-HC | 功能描述:DC/DC转换器 15W DC/DC 1.6kV REG 36-75Vin 12Vout RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| RP15-4812SA-HC | 功能描述:DC/DC转换器 15W DC/DC 1.6kV REG 36-75Vin 12Vout RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
发布紧急采购，3分钟左右您将得到回复。