- 您现在的位置：买卖IC网 > PDF目录21893 > RPM882-H14E2A (Rohm Semiconductor)MODULE IRDA 115.2KBPS 8SMD PDF资料下载
参数资料
| 型号： | RPM882-H14E2A |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 8/10页 |
| 文件大小： | 94K |
| 描述： | MODULE IRDA 115.2KBPS 8SMD |
| 标准包装： | 2,500 |
| 系列： | * |
| 数据速率： | 115.2kbs（SIR） |
| 电源电压： | 2.4 V ~ 3.6 V |
| 无效电流，标准值@ 25° C： | 80µA |
| 通信距离，低功率： | 20cm，60cm |
| 方向： | 侧视图 |
| 工作温度： | -25°C ~ 85°C |
| 尺寸： | 8mm x 2.9mm x 2.2mm |
| 标准： | IrPHY 1.2 |
| 关机： | * |
| 包装： | 带卷 (TR) |
RPM882-H14
Photo Link Module
8/9
Attached components
Recommended values
Part symbol
C1
Recommended value
Notice
1礔, tantalum or ceramic
Ex.) TCFGA1A105M8R (ROHM)
Bigger capacitance is recommended with much noise from power supply
R1
4.7&?%, 1/8W
(VLEDVCC=3V)
At LED Emitting Duty=20%
[LED current set-up method for Remote control mode]
In case of using R1 with different condition from the above, formula is as follows :
LED resistance value : R1[&], LED average consumption current : ILED[mA], Supply voltage : VLEDVCC[V],
minimum necessary of irradiant intensity le1 [mW / sr]
(Including LEDs distribution within ?5deg)
R1=166 ?(VLEDVCC1.28) / le15.0
ILED=Duty ?(VLEDVCC1.28) / (R1+3.5)
Duty : LED duty at emitting
Please set up to be ILED / Duty < 250[mA] (Duty d 50%)
At IrDA Mode, LED current is constantly approximately 40mA.
(Reference) In case of using R1, typical intensity (le1typ) and maximum intensity (le1max) on
axis are described as below.
le1typ=300 ?(VLEDVCC1.28) / (R1+3.5)
le1max=600 ?(VLEDVCC1.28) / (R1+3.5)
Notes
1) LEDVCC (8pin), VCC (3pin) and VIO (2pin)
"
Other power source can be used difference between LEDVCC and VCC and VIO.
(VIO < VCC + 0.3V)
2) Caution in designing board lay-out
To get maximum potential from RPM882-H14, please keep in mind following instruction.
"
The line of RXD (6pin) should be connected at backside via through hole close to RPM882-H14 pin lead. Better not to
be close to photo diode side (1pin).
襎his is to minimize feedback supplied to photo diode from RXD.
"
As for C1 between 1-3 pin should be placed close to RPM882-H14.
"
Better to be placed more than 1.0cm in radius from photo diode (pin1 side) and also away from the parts which
generates noise, such as DC / DC converter.
3) Notes
"
Please be sure to set up the TX-RC (4pin) and the TXD (7pin) input to be L (under 0.3V) except transmitting data
(for < 90祍, ON duty d 50%).
"
Power down current might increase if exposed by strong light (ex. direct sunlight) at powerdown mode.
"
Please use by the signal format at IrDA operating mode which is specified by IrDA Ver1.2 (2.4k to 115.2kbps). There
might be on error if used by different signal format.
"
Please pay attention to the lens carefully.
Dusts of scratch on the lens may effect the characteristics of product. Please handle it with care.
相关PDF资料 |
PDF描述 |
|---|---|
| DK543 | LCD DPM +5V 20V 3.5 DIGIT |
| DK303 | LCD DPM +5V 20V 3.5 DIGIT |
| RPM870-H14E2A | MODULE IRDA 115.2KBPS 8SMD |
| DK502 | LCD DPM +5V 20V 3.5 DIGIT |
| RPM841-H16E4A2 | MODULE IRDA 115.2KBPS 7-SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| RPM882-H7 | 制造商:ROHM 制造商全称:Rohm 功能描述:IrDA Infrared Communication Module |
| RPM882-H7E2 | 制造商:ROHM Semiconductor 功能描述:IRDA COMMUNICATION MODULE SIR - Tape and Reel 制造商:ROHM Semiconductor 功能描述:IC IRDA IR COMMUNICATION MODULE 制造商:ROHM Semiconductor 功能描述:IRDA COMM MOD SIR |
| RPM90 | 功能描述:测试引线 IND. TRIGGER PICK RoHS:否 制造商:Pomona Electronics 设备类型:Patch Cords 连接器类型:Banana plug (stackable) on both ends 长度:60 in 颜色:Black |
| RPM922-H11 | 制造商:ROHM 制造商全称:Rohm 功能描述:IrDA Infrared Communication Module |
| RPM922-H11E2A | 功能描述:光纤发射器、接收器、收发器 IRDA TXRX 0.1152MBPS 3V 7PIN RoHS:否 制造商:Omron Electronics 产品:Transmitters 数据速率:3.5 Gbps 波长:850 nm 最大工作温度: 最小工作温度: 封装 / 箱体: 封装: |
发布紧急采购，3分钟左右您将得到回复。