- 您现在的位置：买卖IC网 > PDF目录16668 > RT555-1/4-0-SP (TE Connectivity)HEAT SHRINK TUBING PDF资料下载
参数资料
| 型号： | RT555-1/4-0-SP |
| 厂商： | TE Connectivity |
| 文件页数： | 4/8页 |
| 文件大小： | 0K |
| 描述： | HEAT SHRINK TUBING |
| 视频文件： | RT-555 Heat Shrinkable Sealing Tape |
| 标准包装： | 500 |
| 系列： | RT-555 |
| 类型： | 套管，半刚性 |
| 收缩比率： | 2 至 1 |
| 内径 - 提供： | 0.252"（6.4mm） |
| 内径 - 恢复： | 0.125"（3.2mm） |
| 已恢复的墙壁厚度： | 0.016"（0.41mm） |
| 材质： | 含氟聚合物 |
| 特点： | 阻燃 |
| 颜色： | 黑 |
| 其它名称： | 9187554002 |
Page 4
4.3.2
4.3.3
4.3.4
4.3.5
4.3.6
4.3.7
SPECIFICATION RT-555 ISSUE 6
Tensile Strength and Ultimate Elongation
Test three specimens of tubing for tensile strength and ultimate elongation in accordance with ASTM D
2671. For tubing sizes 3/8 and smaller, use full sections of tubing. For sizes 1/2 and larger, cut the
specimens with Die D, ASTM D 412. Apply 1-inch (25-mm) centrally located benchmarks to the specimens.
Use an initial machine jaw separation of 1 inch (25 mm) for full sections of tubing and 2 inches (51 mm) for
die cut specimens. Test at a rate of jaw separation of 2.0 ± 0.2 inches (50 ± 5 mm) per minute.
Low Temperature Flexibility
Condition three specimens, each 12 inches (300 mm) in length, and a mandrel selected in accordance with
Table 2, at -65 ± 3oC (-85 ± 5oF) for 4 hours. For tubing sizes 3/4 or less, use whole sections of tubing
recovered on a stranded wire (nearest AWG which is larger than the tubing maximum inside diameter after
unrestricted shrinkage). For tubing sizes larger than 3/4, use 1/4-inch (6.3-mm) wide strips cut from tubing
which has been recovered in accordance with 4.3.1. After 4 hours conditioning, and while still at the
conditioning temperature, wrap the specimens consisting of whole sections of tubing around the mandrel for
not less than 180 degrees in 10 ± 2 seconds. Wrap strip specimens around the mandrel for not less than 360
degrees in 10 ± 2 seconds. Examine the specimens visually for evidence of cracking.
Heat Shock
Condition three 6-inch (150-mm) specimens of tubing for 4 hours in a 300 ± 5oC (572 ± 9oF) oven. Remove
the specimens from the oven, cool to 23 ± 3oC (73 ± 5oF) , wrap 360 degrees around a mandrel selected in
accordance with Table 2 and then visually examine for evidence of dripping, flowing or cracking. Any side
cracking caused by flattening of the specimen on the mandrel shall not constitute failure.
Heat Resistance
Condition three 6-inch (150-mm) specimens prepared in accordance with 4.3.2 for 336 hours in a 250 ± 3oC
(482 ± 5oF) oven. After conditioning, the specimens shall be removed from the oven, cooled to 23 ± 3oC (73
± 5oF) and tested for tensile strength and ultimate elongation in accordance with 4.3.2.
Copper Stability
Slide three 6-inch (150-mm) specimens of tubing over a snug-fitting, straight, clean, bare solid or tubular
copper conductor. Condition the specimens on the conductors for 24 hours in an appropriate humidity
chamber at 90 to 95 percent relative humidity and 23 ± 3oC (73 ± 5oF), followed by 16 hours in a 200 ± 3oC
(392 ± 5oF) oven. After conditioning, remove the specimens from the oven and cool to 23 ± 3oC (73 ± 5oF) .
Remove the copper conductor from the tubing and examine the tubing and conductor. Darkening of the
copper due to normal air oxidation shall not be cause for rejection. Test the tubing for ultimate elongation in
accordance with 4.3.2.
Corrosive Effect
Test the tubing for copper mirror corrosion in accordance with ASTM D 2671, Procedure A, for 16 hours at
200 ± 3oC (392 ± 5oF) . Use specimens of 1/4 x 1 inch (6 x 25 mm) strips cut longitudinally from the tubing.
Evidence of corrosion shall be the removal of copper from the mirror, leaving an area of transparency greater
than 8 percent of its total area.
If this document is printed it becomes uncontrolled. Check for the latest revision.
? 2006 Tyco Electronics Corporation. All rights reserved
相关PDF资料 |
PDF描述 |
|---|---|
| H2MXH-2636M | DIP CABLE - HDM26H/AE26M/X |
| VI-BWJ-EX | CONVERTER MOD DC/DC 36V 75W |
| RNF-150-1-9-SP | HEAT SHRINK TUBING |
| VE-B5J-EW | CONVERTER MOD DC/DC 36V 100W |
| RCC25DREN | CONN EDGECARD 50POS .100 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| RT555-2-0-SP | 功能描述:HEAT SHRINK TUBING RoHS:是 类别:线缆，导线 - 管理 >> 热缩管 系列:RT-555 MSDS 材料安全数据表:HSTT,HSTTA,HSTTV, HSTTVA Series MSDS 标准包装:1 系列:HSTT 类型:套管，弹性 收缩比率:2 至 1 长度:100.0'（30.5m） 内径 - 提供:1.000"（25.4mm） 内径 - 恢复:0.500"（12.7mm） 已恢复的墙壁厚度:0.035"（0.89mm） 材质:聚烯烃 特点:阻燃 颜色:蓝 相关产品:HSG-115V-650-ND - TOOL GUN HEAT SHRINK HI TEMP 10A |
| RT555-2-0-SP-CS7501 | 制造商:TE Connectivity 功能描述:RT555-2-0-SP-CS7501 |
| RT-555-3 | 制造商:MA-COM 制造商全称:M/A-COM Technology Solutions, Inc. 功能描述:High Temperature, Heat-Shrinkable, Fluid Resistant Sealing Sleeves |
| RT555-3/16-0-0.5IN | 制造商:TE Connectivity 功能描述:RT555-3/16-0-0.5IN |
| RT555-3/16-0-0.75IN | 制造商:TE Connectivity 功能描述:RT555-3/16-0-0.75IN |
发布紧急采购，3分钟左右您将得到回复。