- 您现在的位置：买卖IC网 > PDF目录16658 > RT555-5/8-0-SP (TE Connectivity)HEAT SHRINK TUBING PDF资料下载
参数资料
| 型号： | RT555-5/8-0-SP |
| 厂商： | TE Connectivity |
| 文件页数： | 5/8页 |
| 文件大小： | 0K |
| 描述： | HEAT SHRINK TUBING |
| 视频文件： | RT-555 Heat Shrinkable Sealing Tape |
| 标准包装： | 250 |
| 系列： | RT-555 |
| 类型： | 套管，半刚性 |
| 收缩比率： | 2 至 1 |
| 内径 - 提供： | 0.626"（15.9mm） |
| 内径 - 恢复： | 0.313"（7.9mm） |
| 已恢复的墙壁厚度： | 0.022"（0.56mm） |
| 材质： | 含氟聚合物 |
| 特点： | 阻燃剂，防液体 |
| 颜色： | 黑 |
| 其它名称： | 8623434002 |
SPECIFICATION RT-555 ISSUE 6
Page 5
4.3.8
4.3.9
4.3.10
4.4
5.
5.1
5.2
Fluid Resistance
Immerse three 6-inch (150-mm) specimens of tubing, prepared and measured in accordance with 4.3.2,
completely in each listed fluid for the time and temperature specified in Table 3. Use a volume of fluid not
less than 20 times that of the specimens. After immersion, lightly wipe the specimens and air-dry for 30 to
60 minutes at room temperature. Test the specimens from each fluid for tensile strength and ultimate
elongation in accordance with 4.3.2.
Flammability After Fluid Exposure
Flammability tests shall be performed in accordance with ASTM D 2671 Procedure C on a
22-inch (559-mm) length of the tubing that has been fully immersed for 24 hours with ends open in fluids
specified in Table 3. The outside of the tubing shall be wiped to remove excess fluid and mounted in the
apparatus. The inside of the tubing shall be allowed to drain for 5 minutes before flame is applied.
Radiation Resistance
Three specimens prepared in accordance with Section 4.3.2 shall be subjected to gamma radiation for a total
dosage of 10 Mrad at a rate of less than 0.5 Mrad per hour. The specimens shall be measured for tensile
strength and ultimate elongation in accordance with Section 4.3.2.
REJECTION AND RETEST
Failure of any sample to conform to any one of the requirements of the specification shall be cause for
rejection of the lot represented. Product which has been rejected may be replaced or reworked to correct the
defect and then resubmitted for acceptance. Before resubmitting, full particulars concerning the rejection and
the action taken to correct the defect shall be furnished to the inspector.
PREPARATION FOR DELIVERY
PACKAGING
Packaging shall be in accordance with good commercial practice.
MARKING
Each container of product shall be permanently and legibly marked with the manufacturer's part number, size,
quantity, manufacturer's identification, lot number and date of manufacture.
If this document is printed it becomes uncontrolled. Check for the latest revision.
? 2006 Tyco Electronics Corporation. All rights reserved
相关PDF资料 |
PDF描述 |
|---|---|
| VE-BT4-EX | CONVERTER MOD DC/DC 48V 75W |
| SFR-1/2-0-SP | HEAT SHRINK TUBING |
| RP-4800-NO.6-0-STK | HEAT SHRINK TUBING |
| RT555-1/2-0-SP | HEAT SHRINK TUBING |
| CB5045-000 | HEAT SHRINK TUBING |
相关代理商/技术参数 |
参数描述 |
|---|---|
| RT555-NO.1-0-SP | 制造商:TE Connectivity 功能描述: |
| RT-555-T.75-A260-25 | 制造商:TE Connectivity 功能描述: 制造商:TE Connectivity 功能描述:RT-555-T.75-A260-25 |
| RT-555-T.75-A260-50 | 制造商:TE Connectivity 功能描述: |
| RT-555-T1.0-A260-25 | 制造商:TE Connectivity 功能描述:RT-555-T1.0-A260-25 制造商:TE Connectivity 功能描述:Tapes Single Side Adhesive Fluoropolymer Ethylene Tetrafluoroethylene 7.77m |
| RT-555-T1.0-A260-50 | 制造商:TE Connectivity 功能描述:RT-555-T1.0-A260-50 |
发布紧急采购，3分钟左右您将得到回复。