- 您现在的位置：买卖IC网 > PDF目录297329 > RT9183H-18CS (Richtek Technology Corporation) Ultra Low Dropout 1.5A Linear Regulator PDF资料下载
参数资料
| 型号： | RT9183H-18CS |
| 厂商： | Richtek Technology Corporation |
| 英文描述： | Ultra Low Dropout 1.5A Linear Regulator |
| 中文描述： | 1.5A的超低压差线性稳压器 |
| 文件页数： | 15/15页 |
| 文件大小： | 337K |
| 代理商： | RT9183H-18CS |
RT9183
Preliminary
9
DS9183-02 December 2003
www.richtek.com
INPUT CAPACITOR
An input capacitance of
10F is required between the
device input pin and ground directly (the amount of the
capacitance may be increased without limit). The input
capacitor MUST be located less than 1 cm from the device
to assure input stability (see PCB Layout Section). A lower
ESR capacitor allows the use of less capacitance, while
higher ESR type (like aluminum electrolytic) require more
capacitance.
Capacitor types (aluminum, ceramic and tantalum) can be
mixed in parallel, but the total equivalent input capacitance/
ESR must be defined as above to stable operation.
There are no requirements for the ESR on the input
capacitor, but tolerance and temperature coefficient must
be considered when selecting the capacitor to ensure the
capacitance will be
10F over the entire operating
temperature range.
OUTPUT CAPACITOR
The RT9183 is designed specifically to work with very
small ceramic output capacitors. The recommended
minimum capacitance (temperature characteristics X7R or
X5R) are 10
F to 47F range with 10m to 25m range
ceramic capacitors between each LDO output and GND for
transient stability, but it may be increased without limit.
Higher capacitance values help to improve transient.
The output capacitor's ESR is critical because it forms a
zero to provide phase lead which is required for loop
stability. (When using the Y5V dielectric, the minimum
value of the input/output capacitance that can be used for
stable over full operating temperature range is 3.3
F.)
Application Information
Like any low-dropout regulator, the RT9183 series requires
input and output decoupling capacitors. These capacitors
must be correctly selected for good performance (see
Capacitor Characteristics Section). Please note that linear
regulators with a low dropout voltage have high internal
loop gains which require care in guarding against
oscillation caused by insufficient decoupling capacitance.
NO LOAD STABILITY
The device will remain stable and in regulation with no
external load. This is specially important in CMOS RAM
keep-alive applications.
INPUT-OUTPUT (DROPOUT) VOLTAGE
A regulator's minimum input-to-output voltage differential
(dropout voltage) determines the lowest usable supply
voltage. In battery-powered systems, this determines the
useful end-of-life battery voltage. Because the device uses
a PMOS, its dropout voltage is a function of drain-to-source
on-resistance, RDS(ON), multiplied by the load current:
VDROPOUT = VIN - VOUT = RDS(ON) × IOUT
CURRENT LIMIT
The RT9183 monitors and controls the PMOS' gate
voltage, minimum limiting the output current to 2A . The
output can be shorted to ground for an indefinite period of
time without damaging the part.
SHORT-CIRCUIT PROTECTION
The device is short circuit protected and in the event of a
peak over-current condition, the short-circuit control loop
will rapidly drive the output PMOS pass element off. Once
the power pass element shuts down, the control loop will
rapidly cycle the output on and off until the average power
dissipation causes the thermal shutdown circuit to respond
to servo the on/off cycling to a lower frequency. Please
refer to the section on thermal information for power
dissipation calculations.
CAPACITOR CHARACTERISTICS
It is important to note that capacitance tolerance and
variation with temperature must be taken into consideration
when selecting a capacitor so that the minimum required
amount of capacitance is provided over the full operating
temperature range. In general, a good tantalum capacitor
will show very little capacitance variation with temperature,
but a ceramic may not be as good (depending on dielectric
type). Aluminum electrolytics also typically have large
temperature variation of capacitance value.
相关PDF资料 |
PDF描述 |
|---|---|
| RT9204CS | Dual Regulator - Standard Buck PWM DC-DC and Linear Power Controller |
| RT9205ACS | Dual Regulators - Synchronous Buck PWM DC-DC and Linear Controller |
| RTB-1.5-2P | 2 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SOLDER |
| RTB-1.5-3P | 3 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SOLDER |
| RTB-1.5-4P | 4 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SOLDER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| RT9183HGM5 | 功能描述:IC REG LDO ADJ 1.5A TO263-5 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:8V 输入电压:10.5 V ~ 23 V 电压 - 压降（标准）:1.7V @ 40mA 稳压器数量:1 电流 - 输出:100mA（最小值） 电流 - 限制（最小）:- 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:剪切带 (CT) 产品目录页面:1075 (CN2011-ZH PDF) 其它名称:296-24390-1 |
| RT9183HGS | 制造商:Richtek Technology Corporation 功能描述:IC REG LDO ADJ 1.5A 8SOP 制造商:Richtek Technology Corporation 功能描述:Ultra Low Dropout 1.5A Linear Regulator |
| RT9183HPM5 | 制造商:Richtek 功能描述:1.5A LDO Regulator |
| RT9183HPS | 制造商:Richtek 功能描述:1.5A LDO Regulator |
| RT9186AGF | 功能描述:IC REG LDO ADJ .5A 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 产品培训模块:More Information on LDOs 标准包装:50 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:最高 15V 电压 - 压降（标准）:1.1V @ 800mA 稳压器数量:1 电流 - 输出:800mA 电流 - 限制（最小）:800mA 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-4，D²Pak（3 引线+接片），TO-263AA 供应商设备封装:D2PAK-3 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。