- 您现在的位置：买卖IC网 > PDF目录69323 > RV5C387A-F (RICOH COMPANY LTD) 0 TIMER(S), REAL TIME CLOCK, PDSO10 PDF资料下载
参数资料
| 型号： | RV5C387A-F |
| 厂商： | RICOH COMPANY LTD |
| 元件分类： | 时钟/数据恢复及定时提取 |
| 英文描述： | 0 TIMER(S), REAL TIME CLOCK, PDSO10 |
| 封装： | 4 X 2.90 MM, 1.20 MM HEIGHT, SSOP-10 |
| 文件页数： | 27/49页 |
| 文件大小： | 330K |
| 代理商： | RV5C387A-F |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页
33
RV5C387A
Course (A)
When the time count precision of each real-time clock is not to be adjusted, the crystal oscillator intended for use
with that real-time clock may have any CL value requiring no presetting. The crystal oscillator may be subject to
frequency variations which are selectable within the allowable range of time count precision. Several crystal
oscillators and real-time clocks should be used to find the center frequency of the crystal oscillators by the method
described in “2.2 Measurement of Oscillation Frequency” and then calculate an appropriate oscillation adjustment
value by the method described in “2.4 Oscillation Adjustment Circuit” for writing this value to the RV5C387A.
Course (B)
When the time count precision of each real-time clock is to be adjusted within the oscillation frequency variations of
the crystal oscillator plus the frequency variations of the real-time clock ICs, it becomes necessary to correct
deviations in the time count of each real-time clock by the method described in “2.4 Oscillation Adjustment Circuit”.
Such oscillation adjustment provides crystal oscillators with a wider range of allowable settings of their oscillation
frequency variations and their CL values. The real-time clock IC and the crystal oscillator intended for use with that
real-time clock IC should be used to find the center frequency of the crystal oscillator by the method described in
“2.2 Measurement of Oscillation Frequency” and then confirm the center frequency thus found to fall within the
range adjustable by the oscillation adjustment circuit before adjusting the oscillation frequency of the oscillation
circuit. At normal temperature, the oscillation frequency of the oscillator circuit can be adjusted by up to
approximately ±1.5ppm.
Course (C)
Course (C) together with Course (D) requires adjusting the time count precision of each real-time clock as well as
the frequency of 32.768-kHz clock pulses output from the 32KOUT pin. Normally, the oscillation frequency of the
crystal oscillator intended for use with the real-time clocks should be adjusted by adjusting the oscillation stabilizing
capacitors CG and CD connected to both ends of the crystal oscillator. The RV5C387A, which incorporates the CG
and the CD, require adjusting the oscillation frequency of the crystal oscillator through its CL value.
Generally, the relationship between the CL value and the CG and CD values can be represented by the following
equation:
CL =
CG
× CD
+ CS
where “CS” represents the floating capacity of the printed circuit board
CG + CD
The crystal oscillator intended for use with the RV5C387A is recommended to have the CL value on the order of 6 to
8pF. Its oscillation frequency should be measured by the method described in “2.2 Measurement of Oscillation
Frequency”. Any crystal oscillator found to have an excessively high or low oscillation frequency (causing a time
count gain or loss, respectively) should be replaced with another one having a smaller and greater CL value,
respectively until another one having an optimum CL value is selected. In this case, the bit settings disabling the
oscillation adjustment circuit (see “2.4 Oscillation Adjustment Circuit”) should be written to the oscillation
adjustment register.
相关PDF资料 |
PDF描述 |
|---|---|
| RX-4571LC | REAL TIME CLOCK, PDSO12 |
| RX-4571SA | REAL TIME CLOCK, PDSO14 |
| RX-4571SA | 0 TIMER(S), REAL TIME CLOCK, PDSO14 |
| RX-4574SG | 0 TIMER(S), REAL TIME CLOCK, PDSO16 |
| RX-4591CF | 0 TIMER(S), REAL TIME CLOCK, PDSO10 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| RV5LAYSB102A | 制造商: 功能描述: 制造商:undefined 功能描述: |
| RV5LAYSB254A | 制造商: 功能描述: 制造商:undefined 功能描述: |
| RV5LAYSD501A | 制造商:n/a 功能描述:RV5LAYSD501 |
| RV5MJKSME-S1 | 功能描述:REVCONN CAT5E JACK METAL 制造商:belden inc. 系列:- 零件状态:在售 样式:模块 外部类型（适配器端）:模块插孔 8p8c（RJ45 以太网） 内部类型（适配器端）:模块插孔 8p8c（RJ45 以太网） 外部壳体材料:- 内部壳体材料:- 外部壳体颜色:灰色 内部壳体颜色:白色 外部触头材料:覆铜 内部触头材料:铜合金 外部触头镀层:金 内部触头镀层:金 工作温度:-10°C ~ 60°C 等级:Cat5e 规格:1G Base-T 特性:屏蔽 外部触头镀层厚度:50μin（1.27μm） 内部触头镀层后的:- 标准包装:1 |
| RV5MJKUBK-S1 | 功能描述:REVCONN CAT5E JACK BLACK 制造商:belden inc. 系列:- 零件状态:在售 样式:模块 外部类型（适配器端）:模块插孔 8p8c（RJ45 以太网） 内部类型（适配器端）:模块插孔 8p8c（RJ45 以太网） 外部壳体材料:- 内部壳体材料:- 外部壳体颜色:黑色 内部壳体颜色:黑色 外部触头材料:覆铜 内部触头材料:铜合金 外部触头镀层:金 内部触头镀层:金 工作温度:-10°C ~ 60°C 等级:Cat5e 规格:1G Base-T 特性:- 外部触头镀层厚度:50μin（1.27μm） 内部触头镀层后的:- 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。