- 您现在的位置：买卖IC网 > Datasheet目录1007 > S202S02 (Sharp Microelectronics)RELAY SSR 240VAC 8A ZC 4-SIP Datasheet资料下载
参数资料
| 型号： | S202S02 |
| 厂商： | Sharp Microelectronics |
| 文件页数： | 8/13页 |
| 文件大小： | 0K |
| 描述： | RELAY SSR 240VAC 8A ZC 4-SIP |
| 标准包装： | 50 |
| 系列： | S202 |
| 电路： | SPST-NO（1 Form A） |
| 输出类型： | AC，过零 |
| 负载电流： | 8A |
| 输入电压： | 1.2VDC |
| 电压 - 负载： | 0 ~ 240 V |
| 安装类型： | 通孔 |
| 端接类型： | PC 引脚 |
| 封装/外壳： | 4-SIP |
| 供应商设备封装： | 4-SIP |
| 包装： | 管件 |
| 继电器类型： | 继电器 |
| 其它名称： | 425-1246-5 |
S102S02 Series
S202S02 Series
■ Design Considerations
● Recommended Operating Conditions
Parameter
Symbol
Conditions
MIN.
MAX.
Unit
Input
Input signal current at ON state
Input signal current at OFF state
I F (ON)
I F (OFF)
?
?
16
0
24
0.1
mA
mA
Load supply voltage
S102S02
S202S02
V OUT (rms)
?
80
80
120
240
V
Output
Load supply current
I OUT (rms)
Locate snubber circuit between output terminals
(Cs = 0.022 μ F, Rs = 47 ? )
0.1
I T (rms)
× 80%( ? )
mA
Frequency
Operating temperature
f
T opr
?
?
47
? 20
63
80
Hz
?C
( ? ) See Fig.2 about derating curve (I T (rms) vs. ambient temperature).
● Design guide
In order for the SSR to turn off, the triggering current (l F ) must be 0.1mA or less.
When the input current (I F ) is below 0.1mA, the output Triac will be in the open circuit mode. However, if the
voltage across the Triac, V D , increases faster than rated dV/dt, the Triac may turn on. To avoid this situation,
please incorporate a snubber circuit. Due to the many different types of load that can be driven, we can
merely recommend some circuit vales to start with : Cs=0.022 μ F and Rs=47 ? . The operation of the SSR
and snubber circuit should be tested and if unintentional switching occurs, please adjust the snubber circuit
component values accordingly.
When making the transition from On to Off state, a snubber circuit should be used ensure that sudden drops
in current are not accompanied by large instantaneous changes in voltage across the Triac.
This fast change in voltage is brought about by the phase difference between current and voltage.
Primarily, this is experienced in driving loads which are inductive such as motors and solenoids.
Following the procedure outlined above should provide sufficient results.
For over voltage protection, a Varistor may be used.
Any snubber or Varistor used for the above mentioned scenarios should be located as close to the main out-
put triac as possible.
Particular attention needs to be paid when utilizing SSRs that incorporate zero crossing circuitry.
If the phase difference between the voltage and the current at the output pins is large enough, zero crossing
type SSRs cannot be used. The result, if zero crossing SSRs are used under this condition, is that the SSR
may not turn on and off irregardless of the input current. In this case, only a non zero cross type SSR should
be used in combination with the above mentioned snubber circuit selection process.
The load current should be within the bounds of derating curve. (Refer to Fig.2)
Also, please use the optional heat sink when necessary.
In case the optional heat sink is used and the isolation voltage between the device and the optional heat sink
is needed, please locate the insulation sheet between the device and the heat sink.
When the optional heat sink is equipped, please set up the M3 screw-fastening torque at 0.3 to 0.5N?m.
In order to dissipate the heat generated from the inside of device effectively, please follow the below sugges-
tions.
Sheet No.: D4-A02401EN
8
相关PDF资料 |
PDF描述 |
|---|---|
| S202S11 | RELAY SSR 240VAC 8A TRIAC 4-SIP |
| S202S12 | RELAY SSR 240VAC 8A ZC 4-SIP |
| S202T01 | RELAY SSR 240VAC 2A TRIAC 4-SIP |
| S202TY1F | RELAY SSR 240VAC 2A TRIAC 4-SIP |
| S205TY2 | RELAY SSR 240VAC 5A ZC 4-SIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| S202S02F | 功能描述:固态继电器-PCB安装 4-SIP ZERO-C 8mA RoHS:否 制造商:Omron Electronics 控制电压范围: 负载电压额定值:40 V 负载电流额定值:120 mA 触点形式:1 Form A (SPST-NO) 输出设备:MOSFET 封装 / 箱体:USOP-4 安装风格:SMD/SMT |
| S202S11 | 功能描述:RELAY SSR 240VAC 8A TRIAC 4-SIP RoHS:否 类别:继电器 >> 固态 系列:S202 其它有关文件:AQx REACH Cert of Compliance 特色产品:AQY Series Relays 标准包装:1 系列:PhotoMOS™ AQY 电路:SPST-NO（1 Form A） 输出类型:AC，DC（RF） 导通状态电阻:1.25 欧姆 负载电流:250mA 输入电压:1.3VDC 电压 - 负载:0 ~ 40 V 安装类型:表面贴装 端接类型:SMD（SMT）接片 封装/外壳:4-SMD（0.175"，4.45mm） 供应商设备封装:4-SSOP 包装:Digi-Reel® 继电器类型:继电器 其它名称:255-2683-6 |
| S202S11F | 功能描述:固态继电器-PCB安装 4-SIP NON-ZC 8mA RoHS:否 制造商:Omron Electronics 控制电压范围: 负载电压额定值:40 V 负载电流额定值:120 mA 触点形式:1 Form A (SPST-NO) 输出设备:MOSFET 封装 / 箱体:USOP-4 安装风格:SMD/SMT |
| S202S12 | 功能描述:RELAY SSR 240VAC 8A ZC 4-SIP RoHS:否 类别:继电器 >> 固态 系列:S202 其它有关文件:AQx REACH Cert of Compliance 特色产品:AQY Series Relays 标准包装:1 系列:PhotoMOS™ AQY 电路:SPST-NO（1 Form A） 输出类型:AC，DC（RF） 导通状态电阻:1.25 欧姆 负载电流:250mA 输入电压:1.3VDC 电压 - 负载:0 ~ 40 V 安装类型:表面贴装 端接类型:SMD（SMT）接片 封装/外壳:4-SMD（0.175"，4.45mm） 供应商设备封装:4-SSOP 包装:Digi-Reel® 继电器类型:继电器 其它名称:255-2683-6 |
| S202S12F | 功能描述:固态继电器-PCB安装 4-SIP Zero Cross 8mA RoHS:否 制造商:Omron Electronics 控制电压范围: 负载电压额定值:40 V 负载电流额定值:120 mA 触点形式:1 Form A (SPST-NO) 输出设备:MOSFET 封装 / 箱体:USOP-4 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。