- 您现在的位置：买卖IC网 > PDF目录26852 > S216S01 (SHARP ELECTRONICS CORP) TRIGGER OUTPUT SOLID STATE RELAY, 4000 V ISOLATION-MAX PDF资料下载
参数资料
| 型号： | S216S01 |
| 厂商： | SHARP ELECTRONICS CORP |
| 元件分类： | 继电器，输入/输出模块 |
| 英文描述： | TRIGGER OUTPUT SOLID STATE RELAY, 4000 V ISOLATION-MAX |
| 封装： | PLASTIC, SIP-4 |
| 文件页数： | 12/13页 |
| 文件大小： | 235K |
| 代理商： | S216S01 |
8
S116S01 Series
S216S01 Series
■ Design Considerations
In order for the SSR to turn off, the triggering current (lF) must be 0.1mA or less.
In phase control applications or where the SSR is being by a pulse signal, please ensure that the pulse width
is a minimum of 1ms.
When the input current (IF) is below 0.1mA, the output Triac will be in the open circuit mode. However, if the
voltage across the Triac, VD, increases faster than rated dV/dt, the Triac may turn on. To avoid this situation,
please incorporate a snubber circuit. Due to the many different types of load that can be driven, we can
merely recommend some circuit vales to start with : Cs=0.1F and Rs=47. The operation of the SSR and
snubber circuit should be tested and if unintentional switching occurs, please adjust the snubber circuit com-
ponent values accordingly.
When making the transition from On to Off state, a snubber circuit should be used ensure that sudden drops
in current are not accompanied by large instantaneous changes in voltage across the Triac.
This fast change in voltage is brought about by the phase difference between current and voltage.
Primarily, this is experienced in driving loads which are inductive such as motors and solenoids.
Following the procedure outlined above should provide sufficient results.
Any snubber or Varistor used for the above mentioned scenarios should be located as close to the main out-
put triac as possible.
The load current should be within the bounds of derating curve. (Refer to Fig.2)
Also, please use the optional heat sink when necessary.
In case the optional heat sink is used and the isolation voltage between the device and the optional heat sink
is needed, please locate the insulation sheet between the device and the heat sink.
When the optional heat sink is equipped, please set up the M3 screw-fastening torque at 0.3 to 0.5Nm.
In order to dissipate the heat generated from the inside of device effectively, please follow the below sugges-
tions.
(a) Make sure there are no warps or bumps on the heat sink, insulation sheet and device surface.
(b) Make sure there are no metal dusts or burrs attached onto the heat sink, insulation sheet and device sur-
face.
(c) Make sure silicone grease is evenly spread out on the heat sink, insulation sheet and device surface.
● Design guide
Sheet No.: D4-A02601EN
● Recommended Operating Conditions
Parameter
S116S01
S216S01
Symbol
Unit
Input
Output
Input signal current at ON state
Input signal current at OFF state
Load supply voltage
Load supply current
Frequency
Operating temperature
IF(ON)
IF(OFF)
VOUT(rms)
IOUT(rms)
f
Topr
mA
V
mA
Hz
C
Locate snubber circuit between output terminals
(Cs
=0.1F, Rs=47)
Conditions
16
0
80
0.1
47
20
24
0.1
120
240
IT(rms)
×80%()
63
80
MIN.
MAX.
() See Fig.2 about derating curve (IT(rms) vs. ambient temperature).
相关PDF资料 |
PDF描述 |
|---|---|
| S21MD3TV | 1 CHANNEL TRIAC OUTPUT OPTOCOUPLER |
| S21ME3F | 1 CHANNEL TRIAC OUTPUT OPTOCOUPLER |
| S21ME8FY | 1 CHANNEL TRIAC OUTPUT WITH ZERO CRSVR OPTOCOUPLER |
| S268P | PIN PHOTO DIODE |
| S26MD02V | TRIGGER OUTPUT SOLID STATE RELAY, 4000 V ISOLATION-MAX |
相关代理商/技术参数 |
参数描述 |
|---|---|
| S216S01F | 功能描述:固态继电器-PCB安装 4-SIP NON-ZC 8mA RoHS:否 制造商:Omron Electronics 控制电压范围: 负载电压额定值:40 V 负载电流额定值:120 mA 触点形式:1 Form A (SPST-NO) 输出设备:MOSFET 封装 / 箱体:USOP-4 安装风格:SMD/SMT |
| S216S02 | 功能描述:RELAY SSR 240VAC 16A ZC 4-SIP RoHS:否 类别:继电器 >> 固态 系列:S216 其它有关文件:AQx REACH Cert of Compliance 特色产品:AQY Series Relays 标准包装:1 系列:PhotoMOS™ AQY 电路:SPST-NO（1 Form A） 输出类型:AC，DC（RF） 导通状态电阻:1.25 欧姆 负载电流:250mA 输入电压:1.3VDC 电压 - 负载:0 ~ 40 V 安装类型:表面贴装 端接类型:SMD（SMT）接片 封装/外壳:4-SMD（0.175"，4.45mm） 供应商设备封装:4-SSOP 包装:Digi-Reel® 继电器类型:继电器 其它名称:255-2683-6 |
| S216S02F | 功能描述:固态继电器-PCB安装 4-SIP ZERO-C 8mA RoHS:否 制造商:Omron Electronics 控制电压范围: 负载电压额定值:40 V 负载电流额定值:120 mA 触点形式:1 Form A (SPST-NO) 输出设备:MOSFET 封装 / 箱体:USOP-4 安装风格:SMD/SMT |
| S216SE1 | 功能描述:RELAY SSR 240VAC 16A TRIAC 4-SIP RoHS:否 类别:继电器 >> 固态 系列:S216 其它有关文件:AQx REACH Cert of Compliance 特色产品:AQY Series Relays 标准包装:1 系列:PhotoMOS™ AQY 电路:SPST-NO（1 Form A） 输出类型:AC，DC（RF） 导通状态电阻:1.25 欧姆 负载电流:250mA 输入电压:1.3VDC 电压 - 负载:0 ~ 40 V 安装类型:表面贴装 端接类型:SMD（SMT）接片 封装/外壳:4-SMD（0.175"，4.45mm） 供应商设备封装:4-SSOP 包装:Digi-Reel® 继电器类型:继电器 其它名称:255-2683-6 |
| S216SE1F | 功能描述:固态继电器-PCB安装 4-SIP NON-ZC 8mA RoHS:否 制造商:Omron Electronics 控制电压范围: 负载电压额定值:40 V 负载电流额定值:120 mA 触点形式:1 Form A (SPST-NO) 输出设备:MOSFET 封装 / 箱体:USOP-4 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。