- 您现在的位置：买卖IC网 > Datasheet目录1007 > S216S02 (Sharp Microelectronics)RELAY SSR 240VAC 16A ZC 4-SIP Datasheet资料下载
参数资料
| 型号： | S216S02 |
| 厂商： | Sharp Microelectronics |
| 文件页数： | 9/13页 |
| 文件大小： | 0K |
| 描述： | RELAY SSR 240VAC 16A ZC 4-SIP |
| 标准包装： | 50 |
| 系列： | S216 |
| 电路： | SPST-NO（1 Form A） |
| 输出类型： | AC，过零 |
| 负载电流： | 16A |
| 输入电压： | 1.2VDC |
| 电压 - 负载： | 0 ~ 240 V |
| 安装类型： | 通孔 |
| 端接类型： | PC 引脚 |
| 封装/外壳： | 4-SIP |
| 供应商设备封装： | 4-SIP |
| 包装： | 散装 |
| 继电器类型： | 继电器 |
| 其它名称： | 425-1267-5 |
S116S02 Series
S216S02 Series
(a) Make sure there are no warps or bumps on the heat sink, insulation sheet and device surface.
(b) Make sure there are no metal dusts or burrs attached onto the heat sink, insulation sheet and device sur-
face.
(c) Make sure silicone grease is evenly spread out on the heat sink, insulation sheet and device surface.
Silicone grease to be used is as follows;
1) There is no aged deterioration within the operating temperature ranges.
2) Base oil of grease is hardly separated and is hardly permeated in the device.
3) Even if base oil is separated and permeated in the device, it should not degrade the function of a device.
Recommended grease : G-746 (Shin-Etsu Chemical Co., Ltd.)
: G-747 (Shin-Etsu Chemical Co., Ltd.)
: SC102 (Dow Corning Toray Silicone Co., Ltd.)
In case the optional heat sink is screwed up, please solder after screwed.
In case of the lead frame bending, please keep the following minimum distance and avoid any mechanical
stress between the base of terminals and the molding resin.
4.4mm MIN.
Some of AC electromagnetic counters or solenoids have built-in rectifier such as the diode.
In this case, please use the device carefully since the load current waveform becomes similar with rectangu-
lar waveform and this results may not make a device turn off.
● Degradation
In general, the emission of the IRED used in SSR will degrade over time.
In the case where long term operation and / or constant extreme temperature fluctuations will be applied to
the devices, please allow for a worst case scenario of 50% degradation over 5years.
Therefore in order to maintain proper operation, a design implementing these SSRs should provide at least
twice the minimum required triggering current from initial operation.
● Standard Circuit
S116S02
S216S02
R 1
+ V CC
V 1
D 1
3
4
SSR
1
2
Z S
Load
AC Line
Tr1
Z S : Surge absorption circuit (Snubber circuit)
? For additional design assistance, please review our corresponding Optoelectronic Application Notes.
Sheet No.: D4-A02701EN
9
相关PDF资料 |
PDF描述 |
|---|---|
| S228C | RELAY SSR 8A 280VAC .187QC |
| S314-003 | CABLE SCSI I DB25M/C50M 3' |
| S314-006 | CABLE SCSI I DB25M/C50M 6' |
| S322 | RELAY SSR AC OUT 1CH 3A PCB |
| S356-003 | CABLE SCSI II HD50M/C50M 3' |
相关代理商/技术参数 |
参数描述 |
|---|---|
| S216S02F | 功能描述:固态继电器-PCB安装 4-SIP ZERO-C 8mA RoHS:否 制造商:Omron Electronics 控制电压范围: 负载电压额定值:40 V 负载电流额定值:120 mA 触点形式:1 Form A (SPST-NO) 输出设备:MOSFET 封装 / 箱体:USOP-4 安装风格:SMD/SMT |
| S216SE1 | 功能描述:RELAY SSR 240VAC 16A TRIAC 4-SIP RoHS:否 类别:继电器 >> 固态 系列:S216 其它有关文件:AQx REACH Cert of Compliance 特色产品:AQY Series Relays 标准包装:1 系列:PhotoMOS™ AQY 电路:SPST-NO（1 Form A） 输出类型:AC，DC（RF） 导通状态电阻:1.25 欧姆 负载电流:250mA 输入电压:1.3VDC 电压 - 负载:0 ~ 40 V 安装类型:表面贴装 端接类型:SMD（SMT）接片 封装/外壳:4-SMD（0.175"，4.45mm） 供应商设备封装:4-SSOP 包装:Digi-Reel® 继电器类型:继电器 其它名称:255-2683-6 |
| S216SE1F | 功能描述:固态继电器-PCB安装 4-SIP NON-ZC 8mA RoHS:否 制造商:Omron Electronics 控制电压范围: 负载电压额定值:40 V 负载电流额定值:120 mA 触点形式:1 Form A (SPST-NO) 输出设备:MOSFET 封装 / 箱体:USOP-4 安装风格:SMD/SMT |
| S216SE2 | 功能描述:RELAY SSR 240VAC 16A ZC 4-SIP RoHS:否 类别:继电器 >> 固态 系列:S216 其它有关文件:AQx REACH Cert of Compliance 特色产品:AQY Series Relays 标准包装:1 系列:PhotoMOS™ AQY 电路:SPST-NO（1 Form A） 输出类型:AC，DC（RF） 导通状态电阻:1.25 欧姆 负载电流:250mA 输入电压:1.3VDC 电压 - 负载:0 ~ 40 V 安装类型:表面贴装 端接类型:SMD（SMT）接片 封装/外壳:4-SMD（0.175"，4.45mm） 供应商设备封装:4-SSOP 包装:Digi-Reel® 继电器类型:继电器 其它名称:255-2683-6 |
| S216SE2F | 功能描述:固态继电器-PCB安装 4-SIP ZERO-C 8mA RoHS:否 制造商:Omron Electronics 控制电压范围: 负载电压额定值:40 V 负载电流额定值:120 mA 触点形式:1 Form A (SPST-NO) 输出设备:MOSFET 封装 / 箱体:USOP-4 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。