- 您现在的位置：买卖IC网 > PDF目录297338 > S216SE1 (SHARP ELECTRONICS CORP) TRIGGER OUTPUT SOLID STATE RELAY, 3000 V ISOLATION-MAX PDF资料下载
参数资料
| 型号： | S216SE1 |
| 厂商： | SHARP ELECTRONICS CORP |
| 元件分类： | 继电器，输入/输出模块 |
| 英文描述： | TRIGGER OUTPUT SOLID STATE RELAY, 3000 V ISOLATION-MAX |
| 封装： | PLASTIC, SIP-4 |
| 文件页数： | 14/14页 |
| 文件大小： | 243K |
| 代理商： | S216SE1 |
9
S216SE1 Series
Sheet No.: D4-A03401EN
● Degradation
In general, the emission of the IRED used in SSR will degrade over time.
In the case where long term operation and / or constant extreme temperature fluctuations will be applied to
the devices, please allow for a worst case scenario of 50% degradation over 5years.
Therefore in order to maintain proper operation, a design implementing these SSRs should provide at least
twice the minimum required triggering current from initial operation.
Silicone grease to be used is as follows;
1) There is no aged deterioration within the operating temperature ranges.
2) Base oil of grease is hardly separated and is hardly permeated in the device.
3) Even if base oil is separated and permeated in the device, it should not degrade the function of a device.
Recommended grease : G-746 (Shin-Etsu Chemical Co., Ltd.)
: G-747 (Shin-Etsu Chemical Co., Ltd.)
: SC102 (Dow Corning Toray Silicone Co., Ltd.)
In case the optional heat sink is screwed up, please solder after screwed.
In case of the lead frame bending, please keep the following minimum distance and avoid any mechanical
stress between the base of terminals and the molding resin.
Some of AC electromagnetic counters or solenoids have built-in rectifier such as the diode.
In this case, please use the device carefully since the load current waveform becomes similar with
rectangular waveform and this results may not make a device turn off.
Example how to equip optional heat sink for reinforced isolation
1) Case of isolation sheet whose thickness is 0.4mm or more (Viso : 3kV or more)
2) Case of the use of double isolation sheet (Viso : each 3kV or more)
Please keep 5mm distance as minimum between naked metal portion of SSR and heat sink, and also
between naked metal portion of SSR and bis/nut/washer.
However, please avoid the natural rubber for isolation sheet.
4.4mm MIN.
Heat sink
SSR
0.4mm thickness or more
isolation sheet
Heat sink
SSR
Isolation sheet
相关PDF资料 |
PDF描述 |
|---|---|
| S2190-89.4720MHZ | CRYSTAL OSCILLATOR, CLOCK, 89.472 MHz, ACMOS OUTPUT |
| S2234B-FREQ-OUT26 | CRYSTAL OSCILLATOR, CLOCK, 50.001 MHz - 80 MHz, ACMOS/TTL OUTPUT |
| S2234C-FREQ-OUT26 | CRYSTAL OSCILLATOR, CLOCK, 50.001 MHz - 80 MHz, ACMOS/TTL OUTPUT |
| S238B-N-M-0 | 2000 MHz - 18000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 2.8 dB INSERTION LOSS |
| S238B-N-M-1 | 2000 MHz - 18000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 2.8 dB INSERTION LOSS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| S216SE1F | 功能描述:固态继电器-PCB安装 4-SIP NON-ZC 8mA RoHS:否 制造商:Omron Electronics 控制电压范围: 负载电压额定值:40 V 负载电流额定值:120 mA 触点形式:1 Form A (SPST-NO) 输出设备:MOSFET 封装 / 箱体:USOP-4 安装风格:SMD/SMT |
| S216SE2 | 功能描述:RELAY SSR 240VAC 16A ZC 4-SIP RoHS:否 类别:继电器 >> 固态 系列:S216 其它有关文件:AQx REACH Cert of Compliance 特色产品:AQY Series Relays 标准包装:1 系列:PhotoMOS™ AQY 电路:SPST-NO（1 Form A） 输出类型:AC，DC（RF） 导通状态电阻:1.25 欧姆 负载电流:250mA 输入电压:1.3VDC 电压 - 负载:0 ~ 40 V 安装类型:表面贴装 端接类型:SMD（SMT）接片 封装/外壳:4-SMD（0.175"，4.45mm） 供应商设备封装:4-SSOP 包装:Digi-Reel® 继电器类型:继电器 其它名称:255-2683-6 |
| S216SE2F | 功能描述:固态继电器-PCB安装 4-SIP ZERO-C 8mA RoHS:否 制造商:Omron Electronics 控制电压范围: 负载电压额定值:40 V 负载电流额定值:120 mA 触点形式:1 Form A (SPST-NO) 输出设备:MOSFET 封装 / 箱体:USOP-4 安装风格:SMD/SMT |
| S216ULCSAD | 制造商:Panasonic Electric Works 功能描述: |
| S217 | 制造商:Thomas & Betts 功能描述:BRACKET |
发布紧急采购，3分钟左右您将得到回复。