- 您现在的位置：买卖IC网 > PDF目录270895 > S29AL008D55TFNR11 (Spansion Inc.) SSR OCMOS FET 350MA NO 8-DIP PDF资料下载
参数资料
| 型号： | S29AL008D55TFNR11 |
| 厂商： | Spansion Inc. |
| 英文描述： | SSR OCMOS FET 350MA NO 8-DIP |
| 中文描述： | 8兆位（1 M中的x 8-Bit/512亩x 16位），3.0伏的CMOS只引导扇区闪存 |
| 文件页数： | 4/55页 |
| 文件大小： | 1723K |
| 代理商： | S29AL008D55TFNR11 |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页
12
S29AL008D
S29AL008D_00A3 June 16, 2005
Da t a
S h ee t
The internal state machine is set for reading array data upon device power-up,
or after a hardware reset. This ensures that no spurious alteration of the memory
content occurs during the power transition. No command is necessary in this
mode to obtain array data. Standard microprocessor read cycles that assert valid
addresses on the device address inputs produce valid data on the device data
outputs. The device remains enabled for read access until the command register
contents are altered.
See Reading Array Data, on page 19 for more information. Refer to the AC table
for timing specifications and to Figure 13, on page 38 for the timing diagram. ICC1
in the DC Characteristics table represents the active current specification for
reading array data.
Writing Commands/Command Sequences
To write a command or command sequence (which includes programming data
to the device and erasing sectors of memory), the system must drive WE# and
CE# to VIL, and OE# to VIH.
For program operations, the BYTE# pin determines whether the device accepts
program data in bytes or words. Refer to Word/Byte Configuration, on page 11
for more information.
The device features an Unlock Bypass mode to facilitate faster programming.
Once the device enters the Unlock Bypass mode, only two write cycles are re-
quired to program a word or byte, instead of four. The Word/Byte Program
Command Sequence, on page 20 contains details on programming data to the
device using both standard and Unlock Bypass command sequences.
An erase operation can erase one sector, multiple sectors, or the entire device.
Table 2, on page 14 and Table 3, on page 15 indicate the address space that each
sector occupies. A sector address consists of the address bits required to uniquely
select a sector. The Command Definitions, on page 19 contains details on erasing
a sector or the entire chip, or suspending/resuming the erase operation.
After the system writes the autoselect command sequence, the device enters the
autoselect mode. The system can then read autoselect codes from the internal
register (which is separate from the memory array) on DQ7–DQ0. Standard read
cycle timings apply in this mode. Refer to the Autoselect Mode, on page 15 and
Autoselect Command Sequence, on page 20 for more information.
ICC2 in the DC Characteristics table represents the active current specification for
the write mode. The AC Characteristics, on page 38 contains timing specification
tables and timing diagrams for write operations.
Program and Erase Operation Status
During an erase or program operation, the system may check the status of the
operation by reading the status bits on DQ7–DQ0. Standard read cycle timings
for more information, and to AC Characteristics, on page 38 for timing diagrams.
Standby Mode
When the system is not reading or writing to the device, it can place the device
in the standby mode. In this mode, current consumption is greatly reduced, and
the outputs are placed in the high impedance state, independent of the OE#
input.
相关PDF资料 |
PDF描述 |
|---|---|
| S29AL008D70TFNR11 | 8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| S29AL008D90TFNR11 | 8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| S29AL008D55BFNR11 | IC, SOLID STATE RELAY, 2 FORM A, 100V, 350MA |
| S29AL008D70BFNR11 | 8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| S29AL008D90BFNR11 | 8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
相关代理商/技术参数 |
参数描述 |
|---|---|
| S29AL008D55TFNR12 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| S29AL008D55TFNR13 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| S29AL008D55TFNR20 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| S29AL008D55TFNR21 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| S29AL008D55TFNR22 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
发布紧急采购，3分钟左右您将得到回复。