- 您现在的位置：买卖IC网 > PDF目录225140 > S29GL032A90TAIR31 (Spansion Inc.) 64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY PDF资料下载
参数资料
| 型号： | S29GL032A90TAIR31 |
| 厂商： | Spansion Inc. |
| 英文描述： | 64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY |
| 中文描述： | 64兆位32MEGABIT 3.0螺栓只页面模式闪存 |
| 文件页数： | 61/88页 |
| 文件大小： | 1425K |
| 代理商： | S29GL032A90TAIR31 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页当前第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页
62
S29GLxxxA MirrorBit Flash Family
S29GLxxxA_00_A2 January 28, 2005
Ad van c e
Inf o rmation
In all these cases, the system must write the reset command to return the device
to the reading the array (or to erase-suspend-read if the device was previously
in the erase-suspend-program mode).
DQ3: Sector Erase Timer
After writing a sector erase command sequence, the system may read DQ3 to de-
termine whether or not erasure has begun. (The sector erase timer does not
apply to the chip erase command.) If additional sectors are selected for erasure,
the entire time-out also applies after each additional sector erase command.
When the time-out period is complete, DQ3 switches from a “0” to a “1.” If the
time between additional sector erase commands from the system can be as-
sumed to be less than 50 s, the system need not monitor DQ3. See also the
Sector Erase Command Sequence section.
After the sector erase command is written, the system should read the status of
DQ7 (Data# Polling) or DQ6 (Toggle Bit I) to ensure that the device has accepted
the command sequence, and then read DQ3. If DQ3 is “1,” the Embedded Erase
algorithm has begun; all further commands (except Erase Suspend) are ignored
until the erase operation is complete. If DQ3 is “0,” the device will accept addi-
tional sector erase commands. To ensure the command has been accepted, the
system software should check the status of DQ3 prior to and following each sub-
sequent sector erase command. If DQ3 is high on the second status check, the
last command might not have been accepted.
Table 27 shows the status of DQ3 relative to the other status bits.
DQ1: Write-to-Buffer Abort
DQ1 indicates whether a Write-to-Buffer operation was aborted. Under these
conditions DQ1 produces a “1”. The system must issue the Write-to-Buffer-Abort-
Reset command sequence to return the device to reading array data. See Write
Buffer section for more details.
相关PDF资料 |
PDF描述 |
|---|---|
| S29GL032M10BAIR50 | MirrorBit Flash Family |
| S29GL032M10BAIR52 | MirrorBit Flash Family |
| S29GL032M10BAIR53 | MirrorBit Flash Family |
| S29GL032M10BAIR60 | MirrorBit Flash Family |
| S29GL032M10BAIR62 | MirrorBit Flash Family |
相关代理商/技术参数 |
参数描述 |
|---|---|
| S29GL032A90TAIR32 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY |
| S29GL032A90TAIR33 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY |
| S29GL032A90TAIR40 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY |
| S29GL032A90TAIR41 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY |
| S29GL032A90TAIR42 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY |
发布紧急采购，3分钟左右您将得到回复。