- 您现在的位置：买卖IC网 > PDF目录19446 > SA56004ADP,118 (NXP Semiconductors)IC TEMP SENSOR 8-TSSOP PDF资料下载
参数资料
| 型号： | SA56004ADP,118 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 14/43页 |
| 文件大小： | 516K |
| 描述： | IC TEMP SENSOR 8-TSSOP |
| 标准包装： | 1 |
| 功能： | 温度监控系统（传感器） |
| 传感器类型： | 内部和外部 |
| 感应温度： | -40°C ~ 125°C |
| 精确度： | ±3°C（最小值） |
| 拓扑： | ADC（三角积分型），多路复用器，寄存器库 |
| 输出类型： | I²C?/SMBus? |
| 输出警报： | 是 |
| 输出风扇： | 是 |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-TSSOP |
| 包装： | 标准包装 |
| 产品目录页面： | 846 (CN2011-ZH PDF) |
| 配用： | 568-3615-ND - DEMO BOARD I2C |
| 其它名称： | 568-3330-6 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页
SA56004X
All information provided in this document is subject to legal disclaimers.
?NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 7 25 February 2013
14 of 43
NXP Semiconductors
SA56004X
Digital temperature sensor with overtemperature alarms
7.9 Interruption logic and functional description
7.9.1 ALERT
output
The ALERT
output is used to signal Alert interruptions from the device to the SMBus or
other system interrupt handler and it is active LOW. Because this is an open-drain output,
a pull-up resistor (typically 10 kW) to V
DD
is required. Several slave devices can share a
common interrupt line on the same SMBus.
The ALERT
function is very versatile and accommodates three separate operating
modes:
" Temperature comparator
" System interrupt based on temperature
" SMBus Alert Response Address (ARA) response.
The ARA and interrupt modes are different only in how the user interacts with the
SA56004X.
At the end of every temperature reading, digital comparators determine if the readings are
above the HIGH or T_CRIT setpoint or below the LOW setpoint register values. If so, the
corresponding bit in the Status register is set. If the ALERT
mask bit 7 of the Configuration
register is not HIGH, then any bit set in the Status register other than the BUSY (D7) and
OPEN (D2) causes the ALERT
output pin to be active LOW. An alert will be triggered after
any conversion cycle that finds the temperature is out of the limits defined by the setpoint
registers. In order to trigger an ALERT in all alert modes, the ALERT
mask bit 7 of the
Configuration register must be cleared (not HIGH).
7.9.1.1 ALERT
output in comparator mode
When operating the SA56004X in a system that utilizes an SMBus controller not having
an interrupt, the ALERT
output may be operated as a temperature comparator. In this
mode, when the condition that triggered the ALERT to be asserted is no longer present,
the ALERT
output is released as it goes HIGH. In order to use the ALERT
output as a
temperature comparator, bit D0 (the ALERT configure bit) in the ALERT Mode (AM)
register must be set HIGH. This is not the POR default.
7.9.1.2 ALERT
output in interrupt mode
In the interrupt mode, the ALERT
output is used to provide an interrupt signal that remains
asserted until the interrupt service routine has elapsed. In the interrupt operating mode, a
read of the Status register will set the ALERT
mask bit 7 of the Configuration register if
any of the temperature alarm bits of the Status register is set, with exception of BUSY (D7)
and OPEN (D2). This protocol prevents further ALERT
output triggering until the master
device has reset the ALERT
mask bit at the end of the interrupt service routine. The
Status register bits are cleared only upon a read of the Status register by the serial bus
master (see Figure 5
). In order for the ALERT
output to be used as an interrupt, the
ALERT Configure bit D0 of the ALERT Mode (AM) register must be set LOW (POR
default).
相关PDF资料 |
PDF描述 |
|---|---|
| RMA36DTBH | CONN EDGECARD 72POS R/A .125 SLD |
| RSA36DTBD | CONN EDGECARD 72POS R/A .125 SLD |
| 680-015-113R001 | CONN D-SUB 15POS PLUG NKL IP66 |
| TAJW106K016RNJ | CAP TANT 10UF 16V 10% 2312 |
| REC3-2415DR/H1 | CONV DC/DC 3W 24VIN +/-15VOUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SA56004AD-T | 功能描述:板上安装温度传感器 I2C LOC +/- 2OC AND REM +/- 1OC TS RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| SA56004ATK | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:±1 °C accurate, SMBus-compatible, 8-pin, remote/local digital temperature sensor with overtemperature alarms |
| SA56004ATK,118 | 功能描述:板上安装温度传感器 SMBUS-COMPATIBLE REM LOCL DIGI TEMP SENS RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| SA56004ATK118 | 制造商:Rochester Electronics LLC 功能描述: 制造商:NXP 功能描述: 制造商:NXP Semiconductors 功能描述: |
| SA56004BD | 功能描述:板上安装温度传感器 I2C LOC +/- 2OC AND REM +/- 1OC TS RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。