- 您现在的位置：买卖IC网 > PDF目录19445 > SA56004GDP,118 (NXP Semiconductors)IC TEMP SENSOR 8-TSSOP PDF资料下载
参数资料
| 型号： | SA56004GDP,118 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 9/43页 |
| 文件大小： | 516K |
| 描述： | IC TEMP SENSOR 8-TSSOP |
| 标准包装： | 1 |
| 功能： | 温度监控系统（传感器） |
| 传感器类型： | 内部和外部 |
| 感应温度： | -40°C ~ 125°C |
| 精确度： | ±3°C（最小值） |
| 拓扑： | ADC（三角积分型），多路复用器，寄存器库 |
| 输出类型： | I²C?/SMBus? |
| 输出警报： | 是 |
| 输出风扇： | 是 |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-TSSOP |
| 包装： | 标准包装 |
| 其它名称： | 568-3342-6 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页
SA56004X
All information provided in this document is subject to legal disclaimers.
?NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 7 25 February 2013
9 of 43
NXP Semiconductors
SA56004X
Digital temperature sensor with overtemperature alarms
8. Local LOW setpoint (LLS) and Remote LOW temperature setpoints (RLSHB) at 0 癈.
9. Conversion Rate register (CR) is set to 8h; the default value of about 16
conversions/s.
7.5 Starting conversion
Upon POR, the RUN/STOP bit 6 of the configuration register is zero (default condition),
then, the device enters into its free-running operation mode in which the device A/D
converter is enabled and the measurement function is activated. In this mode, the device
cycles the measurements of the local and remote temperature automatically and
periodically. The conversion rate is defined by the programmable conversion rate stored in
the conversion rate register. It also performs comparison between readings and limits of
the temperature in order to set the flags and interruption accordingly at the end of every
conversion. Measured values are stored in the temp registers, results of the limit
comparisons are reflected by the status of the flag bits in the status register and the
interruption is reflected by the logical level of the ALERT
and T_CRIT
output. If the
power-on temperature limit is not suitable, the temp limit values could be written into the
limit registers during the busy-conversion duration of about 38 ms of the first conversion
after power-up. Otherwise, the status register must be read and the configuration bit 7
must be reset in order to recover the device from interruption caused by the undesired
temp limits.
7.6 Low power software standby mode
The device can be placed in a software standby mode by setting the RUN/STOP bit 6 in
the configuration register HIGH (logic 1). In standby, the free-running oscillator is stopped,
the supply current is less than 10 mA if there is no SMBus activity, all data in the registers
is retained. However, the SMBus is still active and reading and writing registers can still be
performed. A one-shot command initiates a single conversion which has the same effect
as any conversion that occurs when the device is in its free-running mode. To restore the
device to free running mode, set the RUN/STOP bit 6 LOW (logic 0).
7.7 Temperature data format
The temperature data can only be read from the Local and Remote Temperature
registers; the setpoint registers (for example, T_CRIT, LOW, HIGH) are read/write.
Both local and remote temperature reading data is represented by an 11-bit,
twos complement word with the Least Significant Bit (LSB) = 0.125 癈. The temperature
setpoint data for the remote channel is also represented by an 11-bit, twos complement
word with the LSB = 0.125 癈. The temperature setpoint data for both the local channel
and the T_CRIT setpoints are represented by 8-bit, twos complement words with the
LSB =1.0 癈. For 11-bit temp data, the data format is a left justified, 16-bit word available
in two 8-bit registers (high byte and low byte). For 8-bit temp data, the data is available in
a single 8-bit register (high byte only).
相关PDF资料 |
PDF描述 |
|---|---|
| QPD-150-12 | POWER SUPPLY ENCLOSED 12V 12.5A |
| AMC22DREN-S734 | CONN EDGECARD 44POS .100 EYELET |
| PM2120-820K-RC | INDUCTOR TOROID 82UH 10% SMD |
| QPD-150-24 | POWER SUPPLY ENCLOSED 24V 6.5A |
| SA56004FDP,118 | IC TEMP SENSOR 8-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SA56004GDP-T | 功能描述:板上安装温度传感器 I2C LOC +/- 2OC AND REM +/- 1OC TS RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| SA56004GD-T | 功能描述:板上安装温度传感器 I2C LOC +/- 2OC AND REM +/- 1OC TS RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| SA56004HD | 功能描述:板上安装温度传感器 I2C LOC +/- 2OC AND REM +/- 1OC TS RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| SA56004HD,112 | 功能描述:板上安装温度传感器 I2C LOC +/- 2OC AND RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| SA56004HD,118 | 功能描述:板上安装温度传感器 I2C LOC +/- 2OC AND RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。