参数资料
型号: SA56004HDP
厂商: NXP Semiconductors N.V.
元件分类: 工业控制
英文描述: +--1 deg Cel accurate, SMBus-compatible, 8-pin, remote-local digital temperature sensor with overtemperature alarms
封装: SA56004AD<SOT96-1 (SO8)|<<http://www.nxp.com/packages/SOT96-1.html<1<week 11, 2005,;SA56004AD<SOT96-1 (SO8)|<<http://www.nxp.com/packages/SOT96-1.html<1<week 11, 20
文件页数: 18/36页
文件大小: 197K
代理商: SA56004HDP
SA56004X_5
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 05 — 22 May 2008
18 of 36
NXP Semiconductors
SA56004X
Digital temperature sensor with overtemperature alarms
LOW. Furthermore, if the Remote HIGH Setpoint High Byte (RHSHB) register is set to a
value less than +127
°
C and the Alert Mask is disabled, then the ALERT output will be
pulled LOW. Note that the OPEN bit itself will not trigger an ALERT.
When the D+ pin is shorted to ground or to D
, the Remote Temperature High Byte
(RTHB) register is loaded with
128
°
C (1000 0000) and the OPEN (bit 2 in the Status
register) will not be set. Since operating the SA56004X is beyond its normal limits, this
temperature reading represents this shorted fault condition. If the value in the Remote
Low Setpoint High Byte (RLSHB) register is more than
128
°
C and the Alert Mask is
disabled, the ALERT output will be pulled LOW.
7.10 SMBus interface
The device can communicate over a standard two-wire serial interface System
Management Bus (SMBus) or compatible I
2
C-bus using SCLK and SDATA. The device
employs four standard SMBus protocols: Write Byte, Read Byte, Receive Byte, and
Send Byte. Data formats of four protocols are shown in
Figure 9
. The following key points
of protocol are important:
The SMBus master initiates data transfer by establishing a START condition (S) and
terminates data transfer by generating a STOP condition (P).
Data is sent over the serial bus in sequences of 9 clock pulses according to each 8-bit
data byte followed by 1-bit status of device acknowledgement (A).
The 7-bit slave address is equivalent to factory-programmed address of the device.
The command byte is equivalent to the address of the selected device register.
The Receive Byte format is used for quicker transfer data from a device reading
register that was previously selected.
相关PDF资料
PDF描述
SA56004AD +--1 deg Cel accurate, SMBus-compatible, 8-pin, remote-local digital temperature sensor with overtemperature alarms
SA56004FDP +--1 deg Cel accurate, SMBus-compatible, 8-pin, remote-local digital temperature sensor with overtemperature alarms
SA56004BDP +--1 deg Cel accurate, SMBus-compatible, 8-pin, remote-local digital temperature sensor with overtemperature alarms
SA56004CDP +--1 deg Cel accurate, SMBus-compatible, 8-pin, remote-local digital temperature sensor with overtemperature alarms
SA56004FD +--1 deg Cel accurate, SMBus-compatible, 8-pin, remote-local digital temperature sensor with overtemperature alarms
相关代理商/技术参数
参数描述
SA56004HDP,118 功能描述:板上安装温度传感器 I2C LOC +/- 2OC AND RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
SA56004HDP-T 功能描述:板上安装温度传感器 I2C LOC +/- 2OC AND REM +/- 1OC TS RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
SA56004HD-T 功能描述:板上安装温度传感器 I2C LOC +/- 2OC AND REM +/- 1OC TS RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
SA56004X 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:1 Degrees Celcious accurate, SMBus-compatible, 8-pin, remote/local digital temperature sensor with over temperature alarms
SA56004XD 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:1 Degrees Celcious accurate, SMBus-compatible, 8-pin, remote/local digital temperature sensor with over temperature alarms