参数资料
型号: SAF-C164CL-8R25M
厂商: INFINEON TECHNOLOGIES AG
元件分类: 微控制器/微处理器
英文描述: 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP80
封装: 0.65 MM PITCH, METRIC, PLASTIC, QFP-80
文件页数: 13/79页
文件大小: 1314K
代理商: SAF-C164CL-8R25M
C164CI/SI
C164CL/SL
Data Sheet
16
V2.0, 2001-05
Interrupt System
With an interrupt response time within a range from just 5 to 12 CPU clocks (in case of
internal program execution), the C164CI is capable of reacting very fast to the
occurrence of non-deterministic events.
The architecture of the C164CI supports several mechanisms for fast and flexible
response to service requests that can be generated from various sources internal or
external to the microcontroller. Any of these interrupt requests can be programmed to
being serviced by the Interrupt Controller or by the Peripheral Event Controller (PEC).
In contrast to a standard interrupt service where the current program execution is
suspended and a branch to the interrupt vector table is performed, just one cycle is
‘stolen’ from the current CPU activity to perform a PEC service. A PEC service implies a
single byte or word data transfer between any two memory locations with an additional
increment of either the PEC source or the destination pointer. An individual PEC transfer
counter is implicity decremented for each PEC service except when performing in the
continuous transfer mode. When this counter reaches zero, a standard interrupt is
performed to the corresponding source related vector location. PEC services are very
well suited, for example, for supporting the transmission or reception of blocks of data.
The C164CI has 8 PEC channels each of which offers such fast interrupt-driven data
transfer capabilities.
A separate control register which contains an interrupt request flag, an interrupt enable
flag and an interrupt priority bitfield exists for each of the possible interrupt sources. Via
its related register, each source can be programmed to one of sixteen interrupt priority
levels. Once having been accepted by the CPU, an interrupt service can only be
interrupted by a higher prioritized service request. For the standard interrupt processing,
each of the possible interrupt sources has a dedicated vector location.
Fast external interrupt inputs are provided to service external interrupts with high
precision requirements. These fast interrupt inputs feature programmable edge
detection (rising edge, falling edge or both edges).
Software interrupts are supported by means of the ‘TRAP’ instruction in combination with
an individual trap (interrupt) number.
Table 3 shows all of the possible C164CI interrupt sources and the corresponding
hardware-related interrupt flags, vectors, vector locations and trap (interrupt) numbers.
Note: Interrupt nodes which are not used by associated peripherals, may be used to
generate software controlled interrupt requests by setting the respective interrupt
request bit (xIR).
相关PDF资料
PDF描述
SAF-C164CL-8RM 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP80
SAK-C164CI-8R25M 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP80
SAF-C165-LM3V 16-BIT, 20 MHz, MICROCONTROLLER, PQFP100
SAF-C165-L25M 16-BIT, 25 MHz, MICROCONTROLLER, PQFP100
SAF-C165-L25F 16-BIT, 25 MHz, MICROCONTROLLER, PQFP100
相关代理商/技术参数
参数描述
SAF-C164CL-8RM 制造商:INFINEON 制造商全称:Infineon Technologies AG 功能描述:16-Bit Single-Chip Microcontroller
SAFC164CM 制造商:INFINEON 制造商全称:Infineon Technologies AG 功能描述:16-Bit Single-Chip Microcontrol ler
SAF-C164CM 制造商:INFINEON 制造商全称:Infineon Technologies AG 功能描述:16-Bit Single-Chip Microcontrol ler
SAF-C164CM-4EF 制造商:INFINEON 制造商全称:Infineon Technologies AG 功能描述:16-Bit Single-Chip Microcontrol ler
SAF-C164CM-4EF AB 功能描述:16位微控制器 - MCU 16-Bit Sngl-Chip 5V 20MHz OTP RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT