参数资料
型号: SAK-XC164CM-8F20F
厂商: INFINEON TECHNOLOGIES AG
元件分类: 微控制器/微处理器
英文描述: 16-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP64
封装: 0.50 MM PITCH, GREEN, PLASTIC, TQFP-64
文件页数: 50/70页
文件大小: 2001K
代理商: SAK-XC164CM-8F20F
XC164CM
Derivatives
Electrical Parameters
Data Sheet
52
V1.4, 2007-03
XTAL1 input current
I
IL
CC –
±20
μA0 V < V
IN < VDDI
Pin capacitance12)
(digital inputs/outputs)
C
IO
CC –
10
pF
1) Keeping signal levels within the limits specified in this table, ensures operation without overload conditions.
For signal levels outside these specifications, also refer to the specification of the overload current
IOV.
2) If XTAL1 is driven by a crystal, reaching an amplitude (peak to peak) of 0.4
× V
DDI is sufficient.
3) This parameter is tested for P3, P9.
4) The maximum deliverable output current of a port driver depends on the selected output driver mode, see
Table 12, Current Limits for Port Output Drivers. The limit for pin groups must be respected.
5) As a rule, with decreasing output current the output levels approach the respective supply level (
VOL VSS,
VOH VDDP). However, only the levels for nominal output currents are guaranteed.
6) This specification is not valid for outputs which are switched to open drain mode. In this case the respective
output will float and the voltage results from the external circuitry.
7) An additional error current (
IINJ) will flow if an overload current flows through an adjacent pin. Please refer to
the definition of the overload coupling factor
KOV.
8) The driver of P3.15 is designed for faster switching, because this pin can deliver the system clock (CLKOUT).
The maximum leakage current for P3.15 is, therefore, increased to 1
μA.
9) During a hardware reset this specification is valid for configuration on P1H.4, P1H.5, P9.4 and P9.5.
After a hardware reset this specification is valid for NMI.
10) The maximum current may be drawn while the respective signal line remains inactive.
11) The minimum current must be drawn to drive the respective signal line active.
12) Not subject to production test - verified by design/characterization.
Table 12
Current Limits for Port Output Drivers
Port Output Driver
Mode
Maximum Output Current
(
I
OLmax, -IOHmax)
1)
1) An output current above |
IOXnom| may be drawn from up to three pins at the same time.
For any group of 16 neighboring port output pins the total output current in each direction (
ΣI
OL and Σ-IOH) must
remain below 50 mA.
Nominal Output Current
(
I
OLnom, -IOHnom)
Strong driver
10 mA
2.5 mA
Medium driver
4.0 mA
1.0 mA
Weak driver
0.5 mA
0.1 mA
Table 11
DC Characteristics (Operating Conditions apply)1) (cont’d)
Parameter
Symbol
Limit Values
Unit Test Condition
Min.
Max.
相关PDF资料
PDF描述
SAF-XC164D-8R20F 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP100
SAF-XC164D-16F40F 16-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP100
SAF-XC164D-8F40F 16-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP100
SAF-XC164D-8R40F 16-BIT, MROM, 40 MHz, MICROCONTROLLER, PQFP100
SAF-XC164GM-16F20F 16-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP64
相关代理商/技术参数
参数描述
SAK-XC164CM-8F20F AA 功能描述:16位微控制器 - MCU MICROCONTROLLER 16-BIT RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT
SAK-XC164CM-8F20FAA 制造商:Rochester Electronics LLC 功能描述: 制造商:Infineon Technologies AG 功能描述:
SAKXC164CM8F20FAAXT 制造商:Infineon Technologies AG 功能描述:MCU 16-Bit XC166 CISC/DSP/RISC 64KB Flash 2.5V/5V 64-Pin TQFP
SAK-XC164CM-8F40F 制造商:Infineon Technologies AG 功能描述:16BIT MCU 64K FLASH TQFP64 164
SAKXC164CM8F40F AA 制造商:Infineon Technologies AG 功能描述: