参数资料
型号: SAK-XC2232N-40F80L
厂商: INFINEON TECHNOLOGIES AG
元件分类: 微控制器/微处理器
英文描述: 16-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP64
封装: 0.50 MM PITCH, GREEN, PLASTIC, LQFP-64
文件页数: 96/110页
文件大小: 1601K
代理商: SAK-XC2232N-40F80L
XC2232N, XC2234N, XC2236N, XC2238N
XC2000 Family / Value Line
Electrical Parameters
Data Sheet
86
V1.3, 2010-04
Direct Drive
When direct drive operation is selected (SYSCON0.CLKSEL = 11
B), the system clock is
derived directly from the input clock signal CLKIN1:
f
SYS = fIN.
The frequency of
f
SYS is the same as the frequency of fIN. In this case the high and low
times of
f
SYS are determined by the duty cycle of the input clock fIN.
Selecting Bypass Operation from the XTAL1
1) input and using a divider factor of 1 results
in a similar configuration.
Prescaler Operation
When prescaler operation is selected (SYSCON0.CLKSEL = 10
B, PLLCON0.VCOBY =
1
B), the system clock is derived either from the crystal oscillator (input clock signal
XTAL1) or from the internal clock source through the output prescaler K1 (= K1DIV+1):
f
SYS = fOSC / K1.
If a divider factor of 1 is selected, the frequency of
f
SYS equals the frequency of fOSC. In
this case the high and low times of
f
SYS are determined by the duty cycle of the input
clock
f
OSC (external or internal).
The lowest system clock frequency results from selecting the maximum value for the
divider factor K1:
f
SYS = fOSC / 1024.
4.7.2.1
Phase Locked Loop (PLL)
When PLL operation is selected (SYSCON0.CLKSEL = 10
B, PLLCON0.VCOBY = 0B),
the on-chip phase locked loop is enabled and provides the system clock. The PLL
multiplies the input frequency by the factor F (
f
SYS = fIN × F).
F is calculated from the input divider P (= PDIV+1), the multiplication factor N (=
NDIV+1), and the output divider K2 (= K2DIV+1):
(F = N / (P
× K2)).
The input clock can be derived either from an external source at XTAL1 or from the on-
chip clock source.
The PLL circuit synchronizes the system clock to the input clock. This synchronization is
performed smoothly so that the system clock frequency does not change abruptly.
Adjustment to the input clock continuously changes the frequency of
f
SYS so that it is
locked to
f
IN. The slight variation causes a jitter of fSYS which in turn affects the duration
of individual TCSs.
1) Voltages on XTAL1 must comply to the core supply voltage
V
DDI1.
相关PDF资料
PDF描述
SAK-XC2236N-24F20L 16-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PQFP64
SST89V58RD2A-33-I-NJE 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQCC44
SPAKMC332GVFV20 32-BIT, 20 MHz, MICROCONTROLLER, PQFP144
ST7263BK4M1/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO34
SPC5200CBV466BR2 466 MHz, MICROPROCESSOR, PBGA272
相关代理商/技术参数
参数描述
SAK-XC2232N-40F80LAA 制造商:Infineon Technologies AG 功能描述:
SAK-XC2234L-20F66L AA 功能描述:16位微控制器 - MCU 16/32b Sngl Chip MCU 32Bit Perform 66MHz RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT
SAK-XC2236N-16F66LAA 制造商:Infineon Technologies AG 功能描述:
SAK-XC2236N-24F40L 功能描述:16位微控制器 - MCU 16 BIT FLASH RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT
SAK-XC2236N-24F40L AA 功能描述:16位微控制器 - MCU 16-Bit Single-Chip MCU w/32 Bit Perform RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT