参数资料
型号: SAK-XC2388C-200F80L
厂商: INFINEON TECHNOLOGIES AG
元件分类: 微控制器/微处理器
英文描述: 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP144
封装: 0.50 MM PITCH, GREEN, PLASTIC, LQFP-144
文件页数: 134/147页
文件大小: 1798K
代理商: SAK-XC2388C-200F80L
XC2387C, XC2388C
XC2000 Family Derivatives / High Line
Electrical Parameters
Data Sheet
87
V1.2, 2010-09
Overload current coupling
factor for digital I/O pins
K
OVD
CC
1.0 x
10
-2
3.0 x
10
-2
I
OV< 0 mA; not
subject to
production test
1.0 x
10
-4
5.0 x
10
-3
I
OV> 0 mA; not
subject to
production test
Absolute sum of overload
currents
Σ|I
OV|
SR
50
mA
not subject to
production test
Digital core supply voltage
for domain M
8)
V
DDIM
CC
1.5
Digital core supply voltage
for domain 1
V
DDI1
CC
1.5
Digital supply voltage for
IO pads and voltage
regulators
V
DDP SR
3.0
5.5
V
Digital ground voltage
V
SS SR
0
V
1) To ensure the stability of the voltage regulators the EVRs must be buffered with ceramic capacitors. Separate
buffer capacitors with the recomended values shall be connected as close as possible to each
V
DDIM and VDDI1
pin to keep the resistance of the board tracks below 2 Ohm. Connect all
V
DDI1 pins together. The minimum
capacitance value is required for proper operation under all conditions (e.g. temperature). Higher values
slightly increase the startup time.
2) Use one Capacitor for each pin.
3) This is the reference load. For bigger capacitive loads, use the derating factors listed in the PAD properties
section.
4) The timing is valid for pin drivers operating in default current mode (selected after reset). Reducing the output
current may lead to increased delays or reduced driving capability (
C
L).
5) The operating frequency range may be reduced for specific device types. This is indicated in the device
designation (...FxxL). 80 MHz devices are marked ...F80L.
6) Overload conditions occur if the standard operating conditions are exceeded, i.e. the voltage on any pin
exceeds the specified range:
V
OV > VIHmax (IOV > 0) or VOV < VILmin ((IOV < 0). The absolute sum of input
overload currents on all pins may not exceed 50 mA. The supply voltages must remain within the specified
limits. Proper operation under overload conditions depends on the application. Overload conditions must not
occur on pin XTAL1 (powered by
V
DDIM).
Table 12
Operating Conditions (cont’d)
Parameter
Symbol
Values
Unit
Note /
Test Condition
Min.
Typ.
Max.
相关PDF资料
PDF描述
SAF-XC2388C-104F100L 32-BIT, FLASH, 100 MHz, RISC MICROCONTROLLER, PQFP144
SAH-XC2388C-200F80L 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP144
SAK-XC2388C-104F80L 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP144
SAH-XC2712X-8F66R 32-BIT, FLASH, 66 MHz, RISC MICROCONTROLLER, PDSO38
SAK-XC2712X-8F66R 32-BIT, FLASH, 66 MHz, RISC MICROCONTROLLER, PDSO38
相关代理商/技术参数
参数描述
SAK-XC2388E-136F128L AA 制造商:Infineon Technologies AG 功能描述:
SAK-XC2712X-8F40R AA 功能描述:16位微控制器 - MCU 16/32b Sngl Chip MCU 32Bit Perform 40MHz RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT
SAK-XC2722X-8F40V AA 功能描述:16位微控制器 - MCU 16/32b Sngl Chip MCU 32Bit Perform 40MHz RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT
SAK-XC2723X-20F66V AA 功能描述:16位微控制器 - MCU 16/32b Sngl Chip MCU 32Bit Perform 66MHz RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT
SAK-XC2733X-20F66L AA 功能描述:16位微控制器 - MCU 16/32b Sngl Chip MCU 32Bit Perform 66MHz RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT