参数资料
型号: SAK-XC886LM-8FFA3V3
厂商: INFINEON TECHNOLOGIES AG
元件分类: 微控制器/微处理器
英文描述: 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP48
封装: PLASTIC, TQFP-48
文件页数: 126/144页
文件大小: 1455K
代理商: SAK-XC886LM-8FFA3V3
XC886/888CLM
Functional Description
Data Sheet
75
V1.2, 2009-07
Table 25 shows the VCO range for the XC886/888.
3.8.1
Recommended External Oscillator Circuits
The oscillator circuit, a Pierce oscillator, is designed to work with both, an external crystal
oscillator or an external stable clock source. It basically consists of an inverting amplifier
and a feedback element with XTAL1 as input, and XTAL2 as output.
When using a crystal, a proper external oscillator circuitry must be connected to both
pins, XTAL1 and XTAL2. The crystal frequency can be within the range of 4 MHz
to 12 MHz. Additionally, it is necessary to have two load capacitances
C
X1 and CX2, and
depending on the crystal type, a series resistor
R
X2, to limit the current. A test resistor RQ
may be temporarily inserted to measure the oscillation allowance (negative resistance)
of the oscillator circuitry.
R
Q values are typically specified by the crystal vendor. The CX1
and
C
X2 values shown in Figure 25 can be used as starting points for the negative
resistance evaluation and for non-productive systems. The exact values and related
operating range are dependent on the crystal frequency and have to be determined and
optimized together with the crystal vendor using the negative resistance method.
Oscillation measurement with the final target system is strongly recommended to verify
the input amplitude at XTAL1 and to determine the actual oscillation allowance (margin
negative resistance) for the oscillator-crystal system.
When using an external clock signal, the signal must be connected to XTAL1. XTAL2 is
left open (unconnected).
The oscillator can also be used in combination with a ceramic resonator. The final
circuitry must also be verified by the resonator vendor. Figure 25 shows the
recommended external oscillator circuitries for both operating modes, external crystal
mode and external input clock mode.
Table 25
VCO Range
f
VCOmin
f
VCOmax
f
VCOFREEmin
f
VCOFREEmax
Unit
150
200
20
80
MHz
100
150
10
80
MHz
相关PDF资料
PDF描述
SAF-XC886LM-8FFA5V 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP48
SAF-XC888C-8FFA3V3 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP64
SAF-XC888C-8FFI5V 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP64
SAK-XC888CLM-8FFA3V3 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP64
SAK-XC888CLM-8FFA5V 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP64
相关代理商/技术参数
参数描述
SAKXC886LM8FFA5VAC 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
SAK-XC886LM-8FFI 5V AC 功能描述:8位微控制器 -MCU 8-Bit Single-Chip 5V 24MHz Flash RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
SAK-XC888-6FFA 制造商:Infineon Technologies AG 功能描述:IC 8BIT MCU FLASH SMD
SAK-XC888-6FFA 5V AC 功能描述:8位微控制器 -MCU MICROCONTROLLER 8-BIT RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
SAK-XC888-6FFI 5V AC 功能描述:8位微控制器 -MCU 8-Bit Single-Chip 5V 24MHz Flash RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT