参数资料
型号: SAK-XE167FM-48FXXL
厂商: INFINEON TECHNOLOGIES AG
元件分类: 微控制器/微处理器
英文描述: RISC MICROCONTROLLER, PQFP144
封装: 0.50 MM PITCH, GREEN, PLASTIC, LQFP-144
文件页数: 12/140页
文件大小: 1096K
代理商: SAK-XE167FM-48FXXL
XE167FM, XE167GM, XE167HM, XE167KM
XE166 Family Derivatives / Base Line
Electrical Parameters
Data Sheet
109
V2.0, 2009-03
Direct Drive
When direct drive operation is selected (SYSCON0.CLKSEL = 11B), the system clock is
derived directly from the input clock signal CLKIN1:
f
SYS = fIN.
The frequency of
f
SYS is the same as the frequency of fIN. In this case the high and low
times of
f
SYS are determined by the duty cycle of the input clock fIN.
Selecting Bypass Operation from the XTAL11) input and using a divider factor of 1 results
in a similar configuration.
Prescaler Operation
When prescaler operation is selected (SYSCON0.CLKSEL = 10B, PLLCON0.VCOBY =
1B), the system clock is derived either from the crystal oscillator (input clock signal
XTAL1) or from the internal clock source through the output prescaler K1 (= K1DIV+1):
f
SYS = fOSC / K1.
If a divider factor of 1 is selected, the frequency of
f
SYS equals the frequency of fOSC. In
this case the high and low times of
f
SYS are determined by the duty cycle of the input
clock
f
OSC (external or internal).
The lowest system clock frequency results from selecting the maximum value for the
divider factor K1:
f
SYS = fOSC / 1024.
Phase Locked Loop (PLL)
When PLL operation is selected (SYSCON0.CLKSEL = 10B, PLLCON0.VCOBY = 0B),
the on-chip phase locked loop is enabled and provides the system clock. The PLL
multiplies the input frequency by the factor F (
f
SYS = fIN × F).
F is calculated from the input divider P (= PDIV+1), the multiplication factor N (=
NDIV+1), and the output divider K2 (= K2DIV+1):
(F = N / (P
× K2)).
The input clock can be derived either from an external source at XTAL1 or from the on-
chip clock source.
The PLL circuit synchronizes the system clock to the input clock. This synchronization is
performed smoothly so that the system clock frequency does not change abruptly.
Adjustment to the input clock continuously changes the frequency of
f
SYS so that it is
locked to
f
IN. The slight variation causes a jitter of fSYS which in turn affects the duration
of individual TCSs.
1) Voltages on XTAL1 must comply to the core supply voltage
VDDI1.
相关PDF资料
PDF描述
SAK-XE167FM-72FXXL 32-BIT, FLASH, RISC MICROCONTROLLER, PQFP144
SAK-XE167KM-48FXXL RISC MICROCONTROLLER, PQFP144
SAM448-20LMB 0-BIT, MICROPROGRAM SEQUENCER, CQCC28
SAM448-20LM 0-BIT, MICROPROGRAM SEQUENCER, CQCC28
SAM448-20L 0-BIT, MICROPROGRAM SEQUENCER, CQCC28
相关代理商/技术参数
参数描述
SAK-XE167FM-72F80L AA 功能描述:16位微控制器 - MCU 16 BIT FLASH RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT
SAKXE167FM72F80LAA 制造商:Infineon Technologies AG 功能描述:MCU 16-Bit XE166 CISC/DSP/RISC 576KB Flash 3.3V/5V 144-Pin LQFP
SAK-XE167FM-72F80LAA 制造商:Rochester Electronics LLC 功能描述: 制造商:Infineon Technologies AG 功能描述:
SAK-XE167GM-48F80L AA 功能描述:IC MCU 16BIT FLASH 144-LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:XE16x 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:260 系列:73S12xx 核心处理器:80515 芯体尺寸:8-位 速度:24MHz 连通性:I²C,智能卡,UART/USART,USB 外围设备:LED,POR,WDT 输入/输出数:9 程序存储器容量:64KB(64K x 8) 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:2K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 5.5 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:68-VFQFN 裸露焊盘 包装:管件
SAK-XE167GM-48F80LAA 功能描述:16位微控制器 - MCU 16 BIT FLASH RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT