- 您现在的位置：买卖IC网 > PDF目录19572 > SC1453ISK3.3TRT (Semtech)IC REG LDO 3.3V .15A SOT-23-5 PDF资料下载
参数资料
| 型号： | SC1453ISK3.3TRT |
| 厂商： | Semtech |
| 文件页数： | 8/15页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 3.3V .15A SOT-23-5 |
| 标准包装： | 1 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 3.3V |
| 输入电压： | 最高 6.5V |
| 电压 - 压降（标准）： | 0.15V @ 150mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 150mA |
| 电流 - 限制（最小）： | 400mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SC-74A，SOT-753 |
| 供应商设备封装： | SOT-23-5 |
| 包装： | 标准包装 |
| 产品目录页面： | 1358 (CN2011-ZH PDF) |
| 其它名称： | SC1453ISK3.3DKR |
NOT RECOMMENDED FOR NEW DESIGN
POWER MANAGEMENT
Applications Information (Cont.)
SC1453
( 125 ? 85 ) = 370 ° C / W
( T J ( MAX ) ? T A ( MAX ) )
Inserting these values into equation (2) gives us:
P D ( MAX ) = ( 3 . 465 ? 2 . 744 ) ? 0 . 150 = 108 mW
Using this figure, we can calculate the maximum thermal
impedance allowable to maintain T J ≤ 125°C:
θ JA ( MAX ) = =
P D ( MAX ) 0 . 108
With the standard SOT-23-5/TSOT-23-5 Land Pattern
shown at the end of this datasheet, and minimum trace
widths, the thermal impedance junction to ambient for
SC1453ISK is 256°C/W. Thus no additional heatsinking
is required for this example.
The junction temperature can be reduced further (or
higher power dissipation can be allowed) by the use of
larger trace widths and connecting PCB copper to the
GND pin (pin 2), which connects directly to the device
substrate. Adding approximately one square inch of PCB
copper to pin 2 will reduce θ JA to approximately
130°C/W and T J(MAX) for the example above to
approximately 100°C for the SOT-23-5 package. The use
of multi layer boards with internal ground/power planes
will lower the junction temperature and improve overall
output voltage accuracy.
Layout Considerations
While layout for linear devices is generally not as critical
as for a switching application, careful attention to detail
will ensure reliable operation.
1) Attaching the part to a larger copper footprint will
enable better heat transfer from the device, especially
on PCBs where there are internal ground and power
planes.
2) Place the input, output and bypass capacitors close
to the device for optimal transient response and device
behaviour.
3) Connect all ground connections directly to the ground
plane. If there is no ground plane, connect to a common
local ground point before connecting to board ground.
? 2008 Semtech Corp.
8
www.semtech.com
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B0Z-CX-F4 | CONVERTER MOD DC/DC 2V 30W |
| 5250-RC | CHOKE RF HASH 100UH 20% FERRITE |
| 5M80ZE64I5N | IC MAX V CPLD 80 LE 64-EQFP |
| VE-B43-CW-B1 | CONVERTER MOD DC/DC 24V 100W |
| V375A8E400BF2 | CONVERTER MOD DC/DC 8V 400W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC1453ISK-XXXTR | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:150mA Ultra Low Dropout Regulator with Low Noise Bypass |
| SC1453ISK-XXXTRT | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:150mA Ultra Low Dropout Regulator with Low Noise Bypass |
| SC1453ITSK1.5TR | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:150mA Ultra Low Dropout Regulator with Low Noise Bypass |
| SC1453ITSK-1.5TR | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:150mA Ultra Low Dropout Regulator with Low Noise Bypass |
| SC1453ITSK-1.5TRT | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:150mA Ultra Low Dropout Regulator with Low Noise Bypass |
发布紧急采购，3分钟左右您将得到回复。