参数资料
| 型号： | SC1592ISTRT |
| 厂商： | Semtech |
| 文件页数： | 6/19页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO ADJ 3A 8SOIC |
| 标准包装： | 1 |
| 稳压器拓扑结构： | 正，可调式 |
| 输出电压： | 可调 |
| 输入电压： | 1.25 V ~ 16 V |
| 电压 - 压降（标准）： | 0.26V @ 3A |
| 稳压器数量： | 1 |
| 电流 - 输出： | 3A |
| 电流 - 限制（最小）： | 5A |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm Width）裸露焊盘 |
| 供应商设备封装： | 8-SOIC-EP |
| 包装： | 标准包装 |
| 产品目录页面： | 1358 (CN2011-ZH PDF) |
| 其它名称： | SC1592ISDKR |
SC1592
POWER MANAGEMENT
Application Information
The SC1592 is a 3A low dropout high performance linear
voltage regulator. The SC1592 can be used for voltage
applications as low as 0.8V and is ideal for down
conversion utilizing dual supply configuration. This allows
for extremely low dropout voltages with excellent load
and line regulation. The SC1592 can be utilized in high
+3.3V Vcntl
C1
2.2uF
+2.5V Vin
CNTL
IN
SC1592
OUT
SENSE
R2
66.5
+1.8V Vout
C3
100uF
voltage applications, with V IN and V CNTL up to 16V, providing
there is adequate thermal management.
C2
22uF
10k
EN
GND
ILIM
R3
53
V OUT = ( 1 +
) ? V REF
SC1592 is designed to meet stringent requirements of
current generation microprocessors and other sensitive
electronic devices. This is possible by employing an
R 2
R 3
V REF = 0 . 8 V typ .
R1
100
I LIM ≈
additional bias source, V CNTL . The voltage of this supply
needs to be at least 1.5V greater than the output voltage
in order to achieve low dropout, typically less then
300mV.
Unlike most of the other high current linear regulators,
the SC1592 provides a programmable current limit which
can be set with a single resistor. The value of the
programming resistor is:
240 ? V OUT
R LIM
where I LIM = selected current limit value
V OUT = regulated output voltage
R LIM = programmable current limit resistor
The SC1592 has a fast transient response that allows it
to handle large load changes associated with high current
applications. Proper selection of the of the output
capacitor and it’s ESR value determines stable operation
and optimizes performance.
The typical application shown in Figure 2 was tested with
a wide range of different capacitors. The circuit was found
to be unconditionally stable with capacitor values from
47 μ F to 330 μ F and ESR ranging from 0.5m Ω to greater
then 75m Ω .
It’s recommended to maintain 5-10mA through the output
divider network in order to have a tight load and line
regulation. Initial accuracy of the internal voltage
reference V REF = 0.8V ± 1% over full temperature range.
This commands the use of 0.5% or better accuracy
resistors to build a precision power supply.
Figure 2
The circuit in Figure 2 shows a typical application of 2.5V
to 1.8V conversion with a 3.3V control supply and the
load range of up to 3A steady state. Considering the
approximate 2W power being dissipated by the pass
element of the SC1592, we are still able to choose an
SO-8 EDP package with T JA = 36.5°C/W mount on the
1sq.in. copper pad allocated for adequate heat transfer.
The ambient temperature in this case should not exceed
50°C. If this temperature range is too restrictive, then
the DDPAK can be utilized, having T JA = 29°C/W mount
on the same size copper pad.
Input capacitor: A minimum of 10 μ F ceramic capacitor
is recommended to be placed directly next to the Vin pin.
This allows for the device being some distance from any
bulk capacitance on the rail. Additionally, bulk
capacitance may be added closely to the input supply
pin of the SC1592 to ensure that Vin does not sag,
improving load transient response.
Output capacitor: A minimum bulk capacitance of 33 μ F,
along with a 0.1 μ F ceramic decoupling capacitor is
recommended. Increasing the bulk capacitance will
improve the overall transient response. The use of
multiple lower value ceramic capacitors in parallel to
achieve the desired bulk capacitance will not cause
stability issues. Although designed for use with ceramic
output capacitors, the SC1592 is extremely tolerant of
output capacitor ESR values and thus will also work
comfortably with tantalum output capacitors.
? 2011 Semtech Corporation
6
www.semtech.com
相关PDF资料 |
PDF描述 |
|---|---|
| SIP21106DR-475-E3 | IC REG LDO 4.75V .15A SC70-5 |
| RYM24DTMT | CONN EDGECARD 48POS R/A .156 SLD |
| X40421V14-AT1 | IC VOLT MON DUAL SUP/SW 14-TSSOP |
| RCM43DTBI | CONN EDGECARD 86POS R/A .156 SLD |
| EYM40DTMH-S189 | CONN EDGECARD 80POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC15A | 制造商:BOURNS 制造商全称:Bourns Electronic Solutions 功能描述:Power Module |
| SC15A-3S1.8 | 制造商:Bourns / JW Miller 功能描述:Module DC-DC 1-OUT 1.8V 15A 10-Pin SIP 制造商:Bourns Inc 功能描述:Module DC-DC 1-OUT 1.8V 15A 10-Pin SIP |
| SC15A-3S1.8-X200 | 制造商:Bourns Inc 功能描述: |
| SC15A-3S1.8-Z | 制造商:Bourns / JW Miller 功能描述:Module DC-DC 1-OUT 1.8V 15A 10-Pin SIP 制造商:Bourns Inc 功能描述:Module DC-DC 1-OUT 1.8V 15A 10-Pin SIP |
| SC15A-3SDAC | 功能描述:DC/DC转换器 3.3V to 1.3-2.5V 15A RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
发布紧急采购，3分钟左右您将得到回复。