参数资料
型号: SC16C554DIB64,157
厂商: NXP Semiconductors
文件页数: 24/55页
文件大小: 0K
描述: IC UART QUAD SOT314-2
标准包装: 800
通道数: 4,QUART
FIFO's: 16 字节
电源电压: 2.5V,3.3V,5V
带自动流量控制功能:
带IrDA 编码器/解码器:
带故障启动位检测功能:
带调制解调器控制功能:
带CMOS:
安装类型: 表面贴装
封装/外壳: 64-LQFP
供应商设备封装: 64-LQFP(10x10)
包装: 托盘
其它名称: 935270063157
SC16C554DIB64
SC16C554DIB64-ND
Philips Semiconductors
SC16C554/554D
Quad UART with 16-byte FIFO and infrared (IrDA) encoder/decoder
Product data
Rev. 05 — 10 May 2004
30 of 55
9397 750 13132
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
7.6 Modem Control Register (MCR)
This register controls the interface with the modem or a peripheral device.
Table 18:
Modem Control Register bits description
Bit
Symbol
Description
7
MCR[7]
Reserved; set to 0.
6
MCR[6]
IR enable.
Logic 0 = Enable the standard modem receive and transmit
input/output interface (normal default condition).
Logic 1 = Enable infrared IrDA receive and transmit inputs/outputs.
While in this mode, the TX/RX output/inputs are routed to the
infrared encoder/decoder. The data input and output levels will
conform to the IrDA infrared interface requirement. As such, while
in this mode, the infrared TX output will be a logic 0 during idle data
conditions.
5
MCR[5]
Reserved; set to 0.
4
MCR[4]
Loop-back. Enable the local loop-back mode (diagnostics). In this
mode the transmitter output (TX) and the receiver input (RX), CTS,
DSR, CD, and RI are disconnected from the SC16C554/554D I/O
pins. Internally the modem data and control pins are connected into a
loop-back data conguration (see Figure 8). In this mode, the receiver
and transmitter interrupts remain fully operational. The Modem
Control Interrupts are also operational, but the interrupts’ sources are
switched to the lower four bits of the Modem Control. Interrupts
continue to be controlled by the IER register.
Logic 0 = Disable loop-back mode (normal default condition).
Logic 1 = Enable local loop-back mode (diagnostics).
3
MCR[3]
OP2, INTx enable. Used to control the modem CD signal in the
loop-back mode.
Logic 0 = Forces INTA-INTD outputs to the 3-State mode during
the 16 mode (normal default condition). In the loop-back mode,
sets OP2 (CD) internally to a logic 1.
Logic 1 = Forces the INTA-INTD outputs to the active mode during
the 16 mode. In the loop-back mode, sets OP2 (CD) internally to a
logic 0.
2
MCR[2]
OP1. This bit is used in the Loop-back mode only. In the loop-back
mode, this bit is used to write the state of the modem RI interface
signal via OP1.
1
MCR[1]
RTS
Logic 0 = Force RTS output to a logic 1 (normal default condition).
Logic 1 = Force RTS output to a logic 0.
Automatic RTS may be used for hardware ow control by enabling
EFR[6]. See Table 21.
0
MCR[0]
DTR
Logic 0 = Force DTR output to a logic 1 (normal default condition).
Logic 1 = Force DTR output to a logic 0.
相关PDF资料
PDF描述
MS27467T17B55P CONN PLUG 55POS STRAIGHT W/PINS
MS27484T8A98S CONN PLUG 3POS STRAIGHT W/SCKT
SC16C554DIA68,518 IC UART QUAD SOT188-2
MS27474E16B8P CONN RCPT 8POS JAM NUT W/PINS
MS27656E19F11P CONN RCPT 11POS WALL MNT W/PINS
相关代理商/技术参数
参数描述
SC16C554IB64 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Quad UART with 16-byte FIFO and infrared (IrDA) encoder/decoder
SC16C554IB64,128 功能描述:UART 接口集成电路 16C 2.5V-5V 4CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC16C554IB64,151 功能描述:UART 接口集成电路 16C 2.5V-5V 4CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC16C554IB64,157 功能描述:UART 接口集成电路 16C 2.5V-5V 4CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC16C554IB80 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Quad UART with 16-byte FIFO and infrared (IrDA) encoder/decoder