参数资料
型号: SC16C752BIBS,151
厂商: NXP Semiconductors
文件页数: 22/47页
文件大小: 0K
描述: IC UART DUAL W/FIFO 32-HVQFN
产品培训模块: Stand-Alone UARTs
标准包装: 490
通道数: 2,DUART
FIFO's: 64 字节
电源电压: 2.5V,3.3V,5V
带自动流量控制功能:
带故障启动位检测功能:
带调制解调器控制功能:
安装类型: 表面贴装
封装/外壳: 32-VFQFN 裸露焊盘
供应商设备封装: 32-HVQFN(5x5)
包装: 托盘
产品目录页面: 828 (CN2011-ZH PDF)
其它名称: 568-3288
935276389151
SC16C752BIBS-S
SC16C752B
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 6 — 30 November 2010
29 of 47
NXP Semiconductors
SC16C752B
5 V, 2.2 V and 2.5 V dual UART, 5 Mbit/s (max.), with 64-byte FIFOs
7.11 Divisor latches (DLL, DLM)
These are two 8-bit registers which store the 16-bit divisor for generation of the baud clock
in the baud rate generator. DLM stores the most significant part of the divisor. DLL stores
the least significant part of the divisor.
Note that DLL and DLM can only be written to before Sleep mode is enabled, i.e., before
IER[4] is set.
7.12 Transmission Control Register (TCR)
This 8-bit register is used to store the receive FIFO threshold levels to stop/start
transmission during hardware/software flow control. Table 20 shows Transmission Control
Register bit settings.
TCR trigger levels are available from 0 bytes to 60 bytes with a granularity of four.
Remark: TCR can only be written to when EFR[4] = logic 1 and MCR[6] = logic 1. The
programmer must program the TCR such that TCR[3:0] > TCR[7:4]. There is no built-in
hardware check to make sure this condition is met. Also, the TCR must be programmed
with this condition before auto-RTS or software flow control is enabled to avoid spurious
operation of the device.
5
EFR[5]
Special character detect.
logic 0 = special character detect disabled (normal default condition)
logic 1 = special character detect enabled. Received data is compared with
Xoff2 data. If a match occurs, the received data is transferred to FIFO and IIR[4]
is set to a logic 1 to indicate a special character has been detected.
4
EFR[4]
Enhanced functions enable bit.
logic 0 = disables enhanced functions and writing to IER[7:4], FCR[5:4],
MCR[7:5]
logic 1 = enables the enhanced function IER[7:4], FCR[5:4], and MCR[7:5] can
be modified, i.e., this bit is therefore a write enable.
3:0
EFR[3:0] Combinations of software flow control can be selected by programming these bits.
Table 19.
Enhanced Feature Register bits description …continued
Bit
Symbol
Description
Table 20.
Transmission Control Register bits description
Bit
Symbol
Description
7:4
TCR[7:4]
receive FIFO trigger level to resume transmission (0 to 60).
3:0
TCR[3:0]
receive FIFO trigger level to halt transmission (0 to 60).
相关PDF资料
PDF描述
SC16C752BIBS,128 IC DUAL UART 64BYTE 32HVQFN
SC16C554BIB80,528 IC UART QUAD W/FIFO 80-LQFP
ATMEGA88-15AZ MCU AVR 8K FLASH 15MHZ 32-TQFP
SC16C752BIB48,151 IC DUAL UART 64BYTE 48LQFP
SC16C752BIB48,157 IC UART DUAL W/FIFO 48-LQFP
相关代理商/技术参数
参数描述
SC16C752BIBS-F 功能描述:UART 接口集成电路 16CB 2.5V-5V 2CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC16C752BIBS-S 功能描述:UART 接口集成电路 2CH. UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC16C752IB48 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Dual UART with 64-byte FIFO
SC16C752IB48,128 功能描述:UART 接口集成电路 Dual UART 64-byte FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC16C752IB48,151 功能描述:UART 接口集成电路 16C 2.5V-5V 2CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel