参数资料
型号: SC16C754BIA68,518
厂商: NXP Semiconductors
文件页数: 7/50页
文件大小: 0K
描述: IC UART QUAD W/FIFO 68-PLCC
产品培训模块: Stand-Alone UARTs
标准包装: 1
通道数: 4,QUART
FIFO's: 64 字节
电源电压: 2.5V,3.3V,5V
带自动流量控制功能:
带故障启动位检测功能:
带调制解调器控制功能:
安装类型: 表面贴装
封装/外壳: 68-LCC(J 形引线)
供应商设备封装: 68-PLCC
包装: 标准包装
产品目录页面: 828 (CN2011-ZH PDF)
其它名称: 568-2050-6
SC16C754B_4
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 04 — 6 October 2008
15 of 51
NXP Semiconductors
SC16C754B
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 64-byte FIFOs
6.5 Interrupts
The SC16C754B has interrupt generation and prioritization (six prioritized levels of
interrupts) capability. The Interrupt Enable Register (IER) enables each of the six types of
interrupts and the INT signal in response to an interrupt generation. The IER can also
disable the interrupt system by clearing bits 7:5 and 3:0. When an interrupt is generated,
the IIR indicates that an interrupt is pending and provides the type of interrupt through
IIR[5:0]. Table 6 summarizes the interrupt control functions.
It is important to note that for the framing error, parity error, and break conditions, LSR[7]
generates the interrupt. LSR[7] is set when there is an error anywhere in the RX FIFO,
and is cleared only when there are no more errors remaining in the FIFO. LSR[4:2] always
represent the error status for the received character at the top of the RX FIFO. Reading
the RX FIFO updates LSR[4:2] to the appropriate status for the new character at the top of
the FIFO. If the RX FIFO is empty, then LSR[4:2] are all zeros.
For the Xoff interrupt, if an Xoff ow character detection caused the interrupt, the interrupt
is cleared by an Xon ow character detection. If a special character detection caused the
interrupt, the interrupt is cleared by a read of the IIR.
Table 6.
Interrupt control functions
IIR[5:0]
Priority
level
Interrupt type
Interrupt source
Interrupt reset method
00 0001
None
none
00 0110
1
receiver line status
OE, FE, PE, or BI errors occur in
characters in the RX FIFO
FE, PE, BI: all erroneous
characters are read from the
RX FIFO.
OE: read LSR
00 1100
2
RX time-out
stale data in RX FIFO
read RHR
00 0100
2
RHR interrupt
DRDY (data ready)
(FIFO disable)
RX FIFO above trigger level
(FIFO enable)
read RHR
00 0010
3
THR interrupt
TFE (THR empty)
(FIFO disable)
TX FIFO passes above trigger level
(FIFO enable)
read IIR or a write to the THR
00 0000
4
modem status
MSR[3:0] = 0
read MSR
01 0000
5
Xoff interrupt
receive Xoff character(s)/special
character
receive Xon character(s)/Read of
IIR
10 0000
6
CTS, RTS
RTS pin or CTS pin change state from
active (LOW) to inactive (HIGH)
read IIR
相关PDF资料
PDF描述
SC26C92C1N,602 IC UART DUAL W/FIFO 40-DIP
SC28L91A1B,551 IC UART SINGLE W/FIFO 44-PQFP
SC28L91A1B,528 IC UART SINGLE W/FIFO 44PQFP
SC28L91A1A,529 IC UART SINGLE W/FIFO 44-PLCC
SCC68692C1A44,512 IC UART DUAL 44-PLCC
相关代理商/技术参数
参数描述
SC16C754BIA68-S 功能描述:UART 接口集成电路 16CB 2.5V-5V 4CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC16C754BIA68-T 功能描述:UART 接口集成电路 4CH. UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC16C754BIB80 制造商:NXP Semiconductors 功能描述:IC UART QUAD 64BYTE FIFO 16C754 制造商:NXP Semiconductors 功能描述:IC, UART, QUAD, 64BYTE FIFO, 16C754 制造商:NXP Semiconductors 功能描述:IC, UART, QUAD, 64BYTE FIFO, 16C754; No. of Channels:4; Data Rate:5Mbps; Supply Voltage Min:2.25V; Supply Voltage Max:5.5V; Digital IC Case Style:LQFP; No. of Pins:80; Operating Temperature Min:-40C; Operating Temperature Max:85C; ;RoHS Compliant: Yes
SC16C754BIB80,528 功能描述:UART 接口集成电路 16CB 2.5V-5V 4CH RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC16C754BIB80,551 功能描述:UART 接口集成电路 16CB 2.5V-5V 4CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel