参数资料
型号: SC16C850IBS,128
厂商: NXP Semiconductors
文件页数: 10/55页
文件大小: 0K
描述: IC UART SGL W/FIFO 32HVQFN
标准包装: 6,000
特点: 可编程
通道数: 1,UART
FIFO's: 128 字节
规程: RS485
电源电压: 2.5 V ~ 3.3 V
带自动流量控制功能:
带IrDA 编码器/解码器:
带故障启动位检测功能:
带调制解调器控制功能:
带CMOS:
安装类型: 表面贴装
封装/外壳: 32-VFQFN 裸露焊盘
供应商设备封装: 32-HVQFN(5x5)
包装: 带卷 (TR)
SC16C850
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 11 November 2010
18 of 55
NXP Semiconductors
SC16C850
2.5 to 3.3 V UART with 128-byte FIFOs and IrDA encoder/decoder
6.11 Sleep mode
Sleep mode is an enhanced feature of the SC16C850 UART. It is enabled when EFR[4],
the enhanced functions bit, is set and when IER[4] bit is set.
6.11.1 Conditions to enter Sleep mode
Sleep mode is entered when:
Modem input pins are not toggling.
The serial data input line, RX, is idle for 4 character time (logic HIGH) and AFCR1[4]
is logic 0. When AFCR1[4] is logic 1 the device will go to sleep regardless of the state
of the RX pin (see Section 7.21 for the description of AFCR1 bit 4).
The TX FIFO and TX shift register are empty.
There are no interrupts pending.
The RX FIFO is empty.
In Sleep mode, the UART clock and baud rate clock are stopped. Since most registers are
clocked using these clocks, the power consumption is greatly reduced.
Remark: Writing to the divisor latches, DLL and DLM, to set the baud clock, must not be
done during Sleep mode. Therefore, it is advisable to disable Sleep mode using IER[4]
before writing to DLL or DLM.
6.11.2 Conditions to resume normal operation
SC16C850 resumes normal operation by any of the following:
Receives a start bit on RX pin.
Data is loaded into transmit FIFO.
A change of state on any of the modem input pins
If the device is awakened by one of the conditions described above, it will return to the
Sleep mode automatically after all the conditions described in Section 6.11.1 are met. The
device will stay in Sleep mode until it is disabled by setting any channel’s IER bit 4 to a
logic 0.
When the SC16C850 is in Sleep mode and the host data bus (D[7:0], A[2:0], IOW, IOR,
CS) remains in steady state, either HIGH or LOW, the Sleep mode supply current will be
in the
μA range as specified in Table 36 “Static characteristics”. If any of these signals is
toggling or floating then the sleep current will be higher.
6.12 Low power feature
A low power feature is provided by the SC16C850 to prevent the switching of the host
data bus from influencing the sleep current. When the pin LOWPWR is activated (logic
HIGH), the device immediately and unconditionally goes into Low power mode. All clocks
are stopped and most host interface pins are isolated to reduce power consumption. The
device only returns to normal mode when the LOWPWR pin is de-asserted. The pin can
be left unconnected because it has an internal pull-down resistor.
相关PDF资料
PDF描述
VE-B7J-IW-F1 CONVERTER MOD DC/DC 36V 100W
SC16IS760IBS,128 IC UART I2C/SPI 24-HVQFN
VE-B7H-IX-F4 CONVERTER MOD DC/DC 52V 75W
VE-B7H-IX-F2 CONVERTER MOD DC/DC 52V 75W
AT32UC3L032-AUR IC MCU AVR32 32K FLASH 48TQFP
相关代理商/技术参数
参数描述
SC16C850IET 功能描述:UART 接口集成电路 16C 2.5-5V 5MBPS UART 128BFIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC16C850IET,115 功能描述:UART 接口集成电路 16C 2.5-5V 5MBPS RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC16C850IET,151 功能描述:UART 接口集成电路 16C 2.5-5V 5MBPS RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC16C850IET,157 功能描述:UART 接口集成电路 16C 2.5-5V 5MBPS RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC16C850IET-G 功能描述:UART 接口集成电路 16C 2.5-5V 5MBPS UART 128BFIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel