参数资料
| 型号： | SC16IS762IPW,112 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 22/60页 |
| 文件大小： | 0K |
| 描述： | IC DUAL UART 64BYTE 28TSSOP |
| 产品培训模块： | Bridge Solutions Stand-Alone UARTs I²C Bus Fundamentals |
| 特色产品： | NXP - I2C Interface |
| 标准包装： | 51 |
| 特点： | 低电流 |
| 通道数： | 2，DUART |
| FIFO's： | 64 字节 |
| 规程： | RS232，RS485 |
| 电源电压： | 2.5V, 3.3V |
| 带自动流量控制功能： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 28-TSSOP |
| 包装： | 管件 |
| 产品目录页面： | 828 (CN2011-ZH PDF) |
| 配用： | 568-4000-ND - DEMO BOARD SPI/I2C TO DUAL UART 568-3510-ND - DEMO BOARD SPI/I2C TO UART |
| 其它名称： | 568-4021-5 935279294112 SC16IS762IPW SC16IS762IPW-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页
SC16IS752_SC16IS762
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2012. All rights reserved.
Product data sheet
Rev. 9 — 22 March 2012
29 of 60
NXP Semiconductors
SC16IS752; SC16IS762
Dual UART with I2C-bus/SPI interface, 64-byte FIFOs, IrDA SIR
8.11 Transmission Control Register (TCR)
This 8-bit register is used to store the RX FIFO threshold levels to stop/start transmission
during hardware/software flow control. Table 22 shows Transmission Control Register bit
settings. If TCR bits are cleared, then selectable trigger levels in FCR are used in place of
TCR.
TCR trigger levels are available from 0 bytes to 60 characters with a granularity of four.
Remark: TCR can only be written to when EFR[4] = logic 1 and MCR[2] = logic 1. The
programmer must program the TCR such that TCR[3:0] > TCR[7:4]. There is no built-in
hardware check to make sure this condition is met. Also, the TCR must be programmed
with this condition before Auto-RTS or software flow control is enabled to avoid spurious
operation of the device.
8.12 Trigger Level Register (TLR)
This 8-bit register is used to store the transmit and received FIFO trigger levels used for
interrupt generation. Trigger levels from 4 to 60 can be programmed with a granularity
of four. Table 23 shows Trigger Level Register bit settings.
Remark: TLR can only be written to when EFR[4] = logic 1 and MCR[2] = logic 1. If
TLR[3:0] or TLR[7:4] are logical 0, the selectable trigger levels via the FIFO Control
Register (FCR) are used for the transmit and receive FIFO trigger levels. Trigger levels
from 4 characters to 60 characters are available with a granularity of four. The TLR should
be programmed for N4, where N is the desired trigger level.
When the trigger level setting in TLR is zero, the SC16IS752/SC16IS762 uses the trigger
level setting defined in FCR. If TLR has non-zero trigger level value, the trigger level
defined in FCR is discarded. This applies to both transmit FIFO and receive FIFO trigger
level setting.
When TLR is used for RX trigger level control, FCR[7:6] should be left at the default state
‘00’.
Table 22.
Transmission Control Register bits description
Bit
Symbol
Description
7:4
TCR[7:4]
RX FIFO trigger level to resume
3:0
TCR[3:0]
RX FIFO trigger level to halt transmission
Table 23.
Trigger Level Register bits description
Bit
Symbol
Description
7:4
TLR[7:4]
RX FIFO trigger levels (4 to 60), number of characters available
3:0
TLR[3:0]
TX FIFO trigger levels (4 to 60), number of spaces available
相关PDF资料 |
PDF描述 |
|---|---|
| ATMEGA168PV-10AUR | MCU AVR 16KB FLASH 10MHZ 32TQFP |
| FT4232HL-REEL | IC USB HS QUAD UART/SYNC 64-LQFP |
| SC16IS752IBS,151 | IC UART DUAL I2C/SPI 32-HVQFN |
| SC16IS752IPW,112 | IC UART DUAL 12C/SPI 28TSSOP |
| SC16C850IBS,151 | IC UART SGL-CH 3.3V 32-HVQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC16IS762IPW-F | 功能描述:UART 接口集成电路 I2C/SPI-UARTBRIDGE W/IRDA AND GPIO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC16IS762IPW-S | 功能描述:IC UART DUAL I2C/SPI 28-TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - UART（通用异步接收器/发送器） 系列:- 标准包装:250 系列:- 特点:* 通道数:2，DUART FIFO's:16 字节 规程:RS232，RS485 电源电压:2.25 V ~ 5.5 V 带并行端口:- 带自动流量控制功能:是 带IrDA 编码器/解码器:是 带故障启动位检测功能:是 带调制解调器控制功能:是 带CMOS:是 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:托盘 其它名称:XR16L2551IM-F-ND |
| SC16IS762IPW-T | 功能描述:IC UART DUAL I2C/SPI 28-TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - UART（通用异步接收器/发送器） 系列:- 标准包装:250 系列:- 特点:* 通道数:2，DUART FIFO's:16 字节 规程:RS232，RS485 电源电压:2.25 V ~ 5.5 V 带并行端口:- 带自动流量控制功能:是 带IrDA 编码器/解码器:是 带故障启动位检测功能:是 带调制解调器控制功能:是 带CMOS:是 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:托盘 其它名称:XR16L2551IM-F-ND |
| SC16IS850LIBS,128 | 功能描述:UART 接口集成电路 UART/12C-BUS/ SPI INTERF.128 FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC16IS850LIBS,151 | 功能描述:UART 接口集成电路 UART/12C-BUS/ SPI INTERF.128 FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。