参数资料
| 型号： | SC173MLTRT |
| 厂商： | Semtech |
| 文件页数： | 17/27页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 3A 10MLPD |
| 产品培训模块： | Power Supplies 101 |
| 标准包装： | 1 |
| 系列： | EcoSpeed® |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.75 V ~ 5.23 V |
| 输入电压： | 3 V ~ 5.5 V |
| 频率 - 开关： | 200kHz ~ 1MHz |
| 电流 - 输出： | 3A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-VFDFN 裸露焊盘 |
| 包装： | 标准包装 |
| 供应商设备封装： | 10-MLPD（3x3） |
| 其它名称： | SC173MLDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
SC173
Applications Information (continued)
increase the ESR of the output capacitors. It is also im-
perative to provide a proper PCB layout as discussed in
I LPK = 3A +
1
2
× 0.511A = 3.26A
the Layout Guidelines section.
Another way to eliminate doubling-pulsing is to add a
Rate of change of load current is
small (~ 10pF) capacitor across the upper feedback resis-
tor, as shown in Figure 8. This capacitor should be left
dI LOAD
dt
=
0.6A
1 m s
unpopulated unless it can be confirmed that double-
pulsing exists. Adding the C TOP capacitor will couple
more ripple into FB to help eliminate the problem. An
optional connection on the PCB should be available for
L × LPK - MAX × dt
C OUT
= I LPK ×
I MAX =maximumloadrelease=3A
I I
V OUT dI LOAD
2 × ( V PK - V OUT )
this capacitor.
C TOP
2 m H ×
-
C OUT
= 3.26A ×
3.26A 3A
1V 0.6A
2 × (1.05V - 1V)
× 1 m s
V OUT
R1
R2
To FB pin
C OUT = 50 m F
Note that C OUT is much smaller in this example, 50μF com-
pared to 207μF based upon a worst-case load release. To
meet the two design criteria of minimum 50μF and maxi-
mum 78m? ESR, select two capacitors rated at 33μF and
15m? ESR or less.
It is recommended that an additional small capacitor be
placed in parallel with C OUT in order to filter high frequen-
cy switching noise.
Stability Considerations
Unstable operation is possible with adaptive on-time
controllers, and usually takes the form of double-pulsing
or ESR loop instability.
Double-pulsing occurs due to switching noise seen at
the FB input or because the FB ripple voltage is too low.
This causes the FB comparator to trigger prematurely af-
ter the minimum off-time has expired. In extreme cases
the noise can cause three or more successive on-times.
Double-pulsing will result in higher ripple voltage at the
output, but in most applications it will not affect opera-
tion. This form of instability can usually be avoided by
providing the FB pin with a smooth, clean ripple signal
that is at least 10mVp-p, which may dictate the need to
? 2010 Semtech Corporation
Figure 8 — Capacitor Coupling to FB Pin
ESR loop instability is caused by insufficient ESR. The
details of this stability issue are discussed in the ESR Re-
quirements section. The best method for checking sta-
bility is to apply a zero-to-full load transient and observe
the output voltage ripple envelope for overshoot and
ringing. Ringing for more than one cycle after the initial
step is an indication that the ESR should be increased.
One simple way to solve this problem is to add trace re-
sistance in the high current output path. A side effect of
adding trace resistance is a decrease in load regulation.
ESR Requirements
A minimum ESR is required for two reasons. One reason
is to generate enough output ripple voltage to provide
10mVp-p at the FB pin (after the resistor divider) to avoid
double-pulsing.
The second reason is to prevent instability due to insuf-
ficient ESR. The on-time control regulates the valley of
the output ripple voltage. This ripple voltage is the sum
of the two voltages. One is the ripple generated by the
ESR, the other is the ripple due to capacitive charging
17
相关PDF资料 |
PDF描述 |
|---|---|
| SC174MLTRT | IC REG BUCK SYNC ADJ 4A 10MLPD |
| SC183CULTRT | IC REG BUCK SYNC ADJ 2A 16MLPQ |
| SC185HULTRT | IC REG BUCK SYNC 1.5V 4A 16MLPQ |
| SC186ULTRT | IC REG BUCK SYNC ADJ 4A 16MLPQ |
| SC189LULTRT | IC REG BUCK SYNC 1.8V 1.5A 6MLPD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC174 | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:4A EcoSpeedTM Synchronous Step-Down Regulator with Optional Ultrasonic Power Save |
| SC1743 | 制造商:ROEBUCK 功能描述:HAND STRETCH FILM |
| SC174EVB | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:4A EcoSpeedTM Synchronous Step-Down Regulator with Optional Ultrasonic Power Save |
| SC174ML.TRT | 制造商:Semtech Corporation 功能描述: |
| SC174MLTRT | 功能描述:IC REG BUCK SYNC ADJ 4A 10MLPD RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:EcoSpeed® 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
发布紧急采购，3分钟左右您将得到回复。