参数资料
| 型号： | SC196ULTRT |
| 厂商： | Semtech |
| 文件页数： | 8/18页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 1.5A 10MLPD |
| 标准包装： | 1 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.8 V ~ 5.5 V |
| 输入电压： | 2.5 V ~ 5.5 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 1MHz |
| 电流 - 输出： | 1.5A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-UFDFN 裸露焊盘 |
| 包装： | 标准包装 |
| 供应商设备封装： | 10-MLPD-UT（3x3） |
| 产品目录页面： | 1357 (CN2011-ZH PDF) |
| 其它名称： | SC196ULDKR |
SC196
POWER MANAGEMENT
Applications Information (Cont.)
if the output voltage decreases by more than 60% of its
programmed value, a soft-start will be invoked.
Current Limit
The PMOS and NMOS power devices of the buck switcher
stage are protected by current limit functions. In the
case of a short to ground on the output, the part enters
frequency foldback mode, which causes the switching
frequency to divide by a factor determined by the output
voltage. This prevents the inductor current from "stair-
casing".
Over-Voltage Protection
Over-voltage protection is provided on the SC196. In the
event of an over-voltage on the output, the PWM drive is
disabled, effectively tri-stating the LX output. The part will
not resume switching until the output voltage has fallen
2% below the regulation voltage.
Soft-Start
The soft-start mode is enabled after every shutdown
PRELIMINARY
the output capacitor. The burst-to-off period in PSAVE will
decrease as the load current reduces.
The PSAVE switching burst frequency is controlled so that
the inductor current ripple is similar to that in PWM mode.
The minimum switching frequency during this period is
limited to 650kHz.
The SC196 automatically detects when to exit PSAVE
mode by monitoring V OUT . For the SC196 to exit PSAVE
mode, the load must be increased, causing V OUT to
decrease until the power save exit threshold is reached.
PSAVE levels are set high to minimize the undershoot
when exiting PSAVE. The lower PSAVE comparator level
is set +0.7% above V OUT , and the upper comparator level
at +1.5% above V OUT , with the exit threshold at -2% below
V OUT .
If PSAVE operation is required, then a 22 μ F output
capacitor must be used.
cycle to limit in-rush current. In conjunction with the
frequency foldback, this controls the maximum current
during start-up. The PMOS current limit is stepped up
1.5%
BURST
OFF
Higher Load
Applied
through seven soft-start levels to the full value by a timer
driven from the internal oscillator. During soft-start, the
switching frequency is stepped through 1/8, 1/4, 1/2
and full internal oscillator frequency. The time at which
0.7%
V OUT
-2%
PSAVE Mode at Light Load
PWM Mode at Medium/
High Load
these steps are made is controlled by the output voltage
reaching prede ? ned threshold levels. When the output
voltage is within 2% of the regulation voltage, soft-start
mode is disabled.
Inductor Current
Power Save Mode Operation
The PSAVE mode may be selected by tying the SYNC/PWM
pin to GND. Selecting PSAVE mode will enable the SC196
to automatically activate/deactivate operation at light
loads, maximizing ef ? ciency across the full load range.
0A
Time
Figure 1 — Power Save Operation
The SC196 automatically detects the load current at which
it should enter PSAVE mode. The SC196 is optimized to
track maximum ef ? ciency with respect to V IN .
In PSAVE mode, V OUT is driven from a lower level to an
upper level by a switching burst. Once the upper level has
been reached, the switching is stopped and the quiescent
current is reduced. V OUT falls from the upper to lower levels
in this low current state as the load current discharges
100% Duty Cycle Operation
The 100% duty cycle mode may be selected by connecting
the MODE pin high. This will allow the SC196 to maintain
output regulation under conditions of low input voltage/
high output voltage conditions.
In 100% duty cycle operation, as the input supply drops
toward the output voltage, the PMOS on-time increases
linearly above the maximum value in ? xed-frequency
operation until the PMOS is active continuously. Once
? 2007 Semtech Corp.
8
www.semtech.com
相关PDF资料 |
PDF描述 |
|---|---|
| SC198AMLTRT | IC REG BUCK SYNC PROG .8A 20MLPQ |
| SC198MLTRT | IC REG BUCK SYNC PROG .6A 20MLPQ |
| SC2440TETRT | IC REG BUCK 2A DL 16TSSOP |
| SC2443MLTRT | IC DUAL SYNC STP-DN CTRLR 24MLPQ |
| SC2446ITETRT | IC SYNC STEP DOWN CTRLR 28-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC197 | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:3.5MHz, 500mA Synchronous Dual Step-Down DC-DC Regulator |
| SC1972 | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:NPN EPITAXIAL PLANAR TYPE(for RF power amplifiers on VHF band Mobile radio applications) |
| SC197EVB | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:3.5MHz, 500mA Synchronous Dual Step-Down DC-DC Regulator |
| SC197ULTRT | 制造商:Semtech Corporation 功能描述:Conv DC-DC Single Step Down 2.9V to 5.5V 18-Pin MLPQ-UT EP T/R 制造商:Semtech Corporation 功能描述:IC DC-DC CONV 3.5MHz MLPQ-18 制造商:Semtech Corporation 功能描述:SC197 Series 0.8 V 500 mA Dual Channel Step-Down Regulator - MLPQ-UT-18 制造商:Semtech Corporation 功能描述:IC, DC-DC CONV, 3.5MHz, MLPQ-18; Primary Input Voltage:5.5V; No. of Outputs:1; Output Voltage:3.3V; Output Current:500mA; No. of Pins:18; Operating Temperature Min:-40C; Operating Temperature Max:85C; Package / Case:18-MLPQ |
| SC198 | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Dual DC-DC Buck Converter with High Current Capability |
发布紧急采购，3分钟左右您将得到回复。