- 您现在的位置：买卖IC网 > Datasheet目录46 > SC424MLTRT (Semtech)IC REG DL BUCK/LINEAR 28MLPQ Datasheet资料下载
参数资料
| 型号： | SC424MLTRT |
| 厂商： | Semtech |
| 文件页数： | 21/29页 |
| 文件大小： | 496K |
| 描述： | IC REG DL BUCK/LINEAR 28MLPQ |
| 标准包装： | 1 |
| 系列： | SmartDrive™ |
| 拓扑： | 降压（降压）（1），线性（LDO）（1） |
| 功能： | 任何功能 |
| 输出数： | 2 |
| 频率 - 开关： | 200kHz ~ 1MHz |
| 电压/电流 - 输出 1： | 可调至 0.75V，6A |
| 电压/电流 - 输出 2： | 5V，150mA |
| 带 LED 驱动器： | 无 |
| 带监控器： | 无 |
| 带序列发生器： | 无 |
| 电源电压： | 3 V ~ 28 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-VFQFN 裸露焊盘 |
| 供应商设备封装： | 28-MLPQ（4x4） |
| 包装： | 标准包装 |
| 其它名称： | SC424MLDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页
SC414/SC424
21
Applications Information (continued)
Note that it is possible to operate the switcher with the
LDO disabled, but the ENL pin must be below the logic
low threshold (0.4V maximum). The table below summa-
rizes the function of the ENL and EN pins, with respect to
the rising edge of ENL.
EN ENL LDO status Switcher status
low low, < 0.4V off
off
high low, < 0.4V off
on
low high, < 2.6V on
off
high high, < 2.6V on
off
low high, > 2.6V on
off
high high, > 2.6V on
on
Figure 12 below shows the ENL voltage thresholds and
their eff ect on LDO and Switcher operation.
AGND
ENL low
threshold
(min 0.4V)
2.6V
2.4V
LDO on
LDO on
LDO off
V
IN
UVLO hysteresis
ENL voltage
Switcher on if EN = high
Switcher on if EN = high
Switcher off by V
IN
UVLO
Figure 12 ENL Thresholds
ENL Logic Control of PWM Operation
When the ENL input is driven above 2.6V, it is impossible to
determine if the LDO output is going to be used to power
the device or not. In self-powered operation where the
LDO will power the device, it is necessary during the LDO
start-up to hold the PWM switching off until the LDO has
reached 90% of the fi nal value. This prevents overloading
the current-limited LDO output during the LDO start-up.
However, if the switcher was previously operating (with
EN/PSV high but ENL at ground, and V5V supplied exter-
nally), then it is undesirable to shut down the switcher. To
prevent this, when the ENL input is above 2.6V (above the
V
IN
UVLO threshold), the internal logic checks the PGOOD
signal. If PGOOD is high, then the switcher is already
running and the LDO will run through the start-up cycle
without aff ecting the switcher. If PGOOD is low, then the
LDO will not allow any PWM switching until the LDO
output has reached 90% of its fi nal value.
Using the On-chip LDO to Bias the SC414/SC424
The following steps must be followed when using the
internal LDO to bias the device.
Connect V5V to VLDO before enabling the LDO.
Any external load on VLDO should not exceed
40mA until the LDO voltage has reached 90% of
f nal value.
Do not connect the EN pin directly to the V5V or
any other supply voltage if Vout is greater than
or equal to 4.5V
Many applications connect the EN pin to V5V and control
the on/off of the LDO and PWM simultaneously with the
ENL pin. This allows one signal to control both the bias
and power output of the SC414. When V
OUT
> 4.5V this
configuration can cause problems due to the parasitic
diodes in the LDO switchover circuitry. After the Vout >
4.5V PWM output is up and running the switchover diodes
can hold up V5V > UVLO even if the ENL pin is grounded,
turning off the LDO. Operating in this way can potentially
damage the part.
Design Procedure
When designing a switch mode supply the input voltage
range, load current, switching frequency, and inductor
ripple current must be specifi ed.
The maximum input voltage (V
INMAX
) is the highest speci-
f ed input voltage. The minimum input voltage ( V
INMIN
) is
determined by the lowest input voltage after evaluating
the voltage drops due to connectors, fuses, switches, and
PCB traces.
The following parameters defi ne the design.
Nominal output voltage (V
OUT
)
Static or DC output tolerance
Transient response
Maximum load current (I
OUT
)
"
"
"
"
"
"
"
相关PDF资料 |
PDF描述 |
|---|---|
| SC4250LISTRT | IC HOT SWAP CTRLR 8-SOIC |
| SC427MLTRT | IC REG DL BUCK/LINEAR 32MLPQ |
| SE95D,112 | IC SENSOR TEMP 2.8-5.5V SOT96-1 |
| SE97BTP,547 | IC TEMP SENSOR DIMM 8HWSON |
| SE98ATP,547 | IC TEMP SENSOR DDR 8-HWSON |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC4-25 | 制造商:JAMECO VALUEPRO 功能描述:CABLE,SHIELDED,4 CONDUCTOR,GRAY,24AWG,25 FEET,ROUND |
| SC4250 | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Negative Voltage Hot Swap Controller |
| SC4250_05 | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Negative Voltage Hot Swap Controller |
| SC4250HISTR | 制造商:Semtech Corporation 功能描述: |
| SC4250HISTRT | 制造商:Semtech Corporation 功能描述:Hot Swap Controller 1-CH -80V 8-Pin SOIC T/R |
发布紧急采购，3分钟左右您将得到回复。