参数资料
| 型号： | SC4517AIMSTRT |
| 厂商： | Semtech |
| 文件页数： | 11/15页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 1.5A 8MSOP |
| 标准包装： | 1 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 可调 |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 1.25MHz |
| 电流 - 输出： | 1.5A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 包装： | 标准包装 |
| 供应商设备封装： | 8-MSOP |
| 其它名称： | SC4517AIMSDKR |
SC4517A
POWER MANAGEMENT
Application Information (Cont.)
T ( s ) = G COMP ( s ) ? G VD ( s ) = 2 . 125 ? 10
? L ?
?
1 +
) ? ( 1 +
The loop gain will be given by:
? 3 R R 2 1
C 4 R 1 + R 2 s
Where:
1
ω p 1 =
R L ? C
( 1 +
s
ω P 1
s
ω Z
s
ω P 2
)
3. Select ω Z such that it is placed at ω P1 to obtain a
-20dB/dec rate to go across the 0dB line.
4. Place a high frequency compensator pole
ω P2 ( ω P2 = π f s ) to get the maximum attenuation of
the switching ripple and high frequency noise with
the adequate phase lag at ω C.
Layout Guidelines:
In order to achieve optimal electrical and thermal
performance for high frequency converters, special
For 1.8V, 2.5V, 3.3V and 5V out applications, their
respective fixed output parts can be used. The FB pins
are connected directly to the outputs. The voltage dividers
(R 1 and R 2 ) have been integrated into the SC4517A
controllers. For other output cases, the adjustable
SC4517A should be used with an external voltage divider.
One integrator is added at origin to increase the DC gain.
ω Z is used to cancel the power stage pole ω P1 so that the
loop gain has –20dB/dec rate when it reaches 0dB line.
ω P2 is placed at half switching frequency to reject high
frequency switching noises. Figure 4 gives the asymptotic
diagrams of the power stage with current loop closed
and its loop gain.
Loop gain T(s)
attention must be paid to the PCB layouts. The goal of
layout optimization is to identify the high di/dt loops and
minimize them. The following guidelines should be used
to ensure proper operation of the converters.
1. A ground plane is suggested to minimize switching
noises and trace losses and maximize heat
transferring.
2. Start the PCB layout by placing the power components
first. Arrange the power circuit to achieve a clean
power flow route. Put all power connections on one
side of the PCB with wide copper filled areas if
possible.
3. The V IN bypass capacitor should be placed next to
the V IN and GND pins.
4. The trace connecting the feedback resistors to the
output should be short, direct and far away from any
noise sources such as switching node and switching
components.
ω p1
ω Z
Power stage
ω C ω P2
5. Minimize the loop including input capacitor, the
SC4517A and freewheeling diode D 2 . This loop passes
high di/dt current. Make sure the trace width is wide
enough to reduce copper losses in this loop.
6. Maximize the trace width of the loop connecting the
inductor, freewheeling diode D 2 and the output
capacitor.
for given switching corner frequency ω C = 2 π f .
2. Place an integrator at the origin to increase DC and
Figure 4. Asymptotic diagrams of power stage with
current loop closed and its loop gain.
The design guidelines for the SC4517A applications are
as following:
1. Set the loop gain crossover corner frequency ω C
c
low frequency gains.
7. Connect the ground of the feedback divider and the
compensation components directly to the GND pin
of the SC4517A by using a separate ground trace.
8. Connect Pin 4 to a large copper area to remove the
IC heat and increase the power capability of the
SC4517A. A few feedthrough holes are required to
connect this large copper area to a ground plane to
further improve the thermal environment of the
SC4517A. The traces attached to other pins should
be as wide as possible for the same purpose.
? 2006 Semtech Corp.
11
www.semtech.com
相关PDF资料 |
PDF描述 |
|---|---|
| SC4518HSETRT | IC REG BUCK 2A 8-SOIC |
| SC4519HSETRT | IC REG BUCK 3A 8-SOIC |
| SC4524ASETRT | IC REG BUCK 2A 8SOIC |
| SC4524BSETRT | IC REG BUCK 2A 8SOIC |
| SC4524CSETRT | IC REG BUCK ADJ 2A 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC4517AIMSXXTRT | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:1.25MHz, 1.5A Step-Down Switching Regulator |
| SC4517EVB-1 | 制造商:Semtech Corporation 功能描述:EVALUATION BOARD 制造商:Semtech Corporation 功能描述:Portable Imvp-Iv And Imvp-Iv+ Single Phase Power Supply Controller |
| SC4517EVB-2 | 制造商:Semtech Corporation 功能描述:12VIN 5VOUT 0.5A IOUT 制造商:Semtech Corporation 功能描述:EVALUATION BOARD 制造商:Semtech Corporation 功能描述:Eval Board for SC4517 Step-Down Switching Regulator 制造商:Semtech Corporation 功能描述:SC4517A, SWITCHING REG, STEP DOWN, EVAL BOARD; Silicon Manufacturer:Semtech; Silicon Core Number:SC4517A; Kit Application Type:Power Management - Voltage Regulator; Application Sub Type:Step Down Switching Regulator ;RoHS Compliant: Yes |
| SC4518H | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:600kHz, 2A Step-Down Switching Regulator |
| SC4518HEVB | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:600kHz, 2A Step-Down Switching Regulator |
发布紧急采购，3分钟左右您将得到回复。