- 您现在的位置：买卖IC网 > Datasheet目录356 > SC618ULTRT (Semtech)IC LED DRIVER PHOTO FLASH 10-MLP Datasheet资料下载
参数资料
| 型号： | SC618ULTRT |
| 厂商： | Semtech |
| 文件页数： | 11/13页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVER PHOTO FLASH 10-MLP |
| 标准包装： | 1 |
| 恒定电流： | 是 |
| 拓扑： | 切换式电容器（充电泵） |
| 输出数： | 1 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 闪灯/白光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 250kHz |
| 电源电压： | 3 V ~ 5.25 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-UFDFN 裸露焊盘 |
| 供应商设备封装： | 10-MLPD（3x3） |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 85°C |
| 产品目录页面： | 1359 (CN2011-ZH PDF) |
| 其它名称： | SC618ULDKR |
NOT RECOMMENDED FOR NEW DESIGN
Applications Information (continued)
SC618
PCB Layout Considerations
The following layout is suggested for a two-layer design.
The capacitors C1 and C2 are the bucket capacitors and
while in flash or spotlight mode. It is critical to maintain
adequate ground plane around the device to maximize
heat transfer and avoid over-temperature shutdown.
each conducts the full load current of up to 500mA pulsed
for one half clock cycle. C3 is the output decoupling
capacitor placed near the VOUT pin. C4 is the input
decoupling capacitor placed near the VIN pin. Multiple
vias should be used whenever it is necessary to change
layers on nets connecting to pins VIN, VOUT, GND, C1-,
C1+, C2- and C2+.
The load current return path is from the ISET sense point
through the resistor and back to the ground pins.
Resistance in this path adds to the total resistance and
has the effect of reducing the LED current by about 4%
per 10mV of DC drop across the return copper trace in
flash mode. For this reason, it is crucial to have a low resis-
tance return path. Place and ground the resistor as close
as possible to the ground pin of the SC618. The trace from
the ISET pin has virtually no current. The ISET trace should
make contact at the pad of the power sense resistor to
minimize the effect of voltage drop between the LED
cathode and the resistor.
Resistor R1 is routed with a very low resistance connec-
tion between R1 and GND pin 3. The sense trace between
Pin 6 and R1 is routed around the ground vias, allowing
the shortest ground return path possible. The sense trace
is connected to R1 at the positive terminal pad for the
most accurate output possible. The bottom copper layer
is mostly a ground plane with no obstructions between
the ground vias. The smaller rectangle to the left con-
nects the input power to VIN pin 1 and input capacitor
C4. The two traces at the lower left are for logic inputs
FLASH and CTRL. The trace to the right is the ISET pin
sense trace. The sense trace is routed out of the path of
the returning ground current.
Thermal Resistance Considerations
The SC618 package is thermally effi cient when the circuit
board layout connects the thermal pad through multiple
vias to the ground plane. The thermal resistance is rated
at 40°C/W, and this rating is dependent on the connec-
tion between the thermal pad and the ground plane. The
layout should keep the junction temperature below the
OTP limit while operating the SC618 within the specified
electrical conditions for I OUT and V ISET . A poor layout may
allow the junction temperature to reach the OTP limit
11
相关PDF资料 |
PDF描述 |
|---|---|
| SC620ULTRT | IC LED DRIVER LINEAR 16-MLPQ |
| SC628AULTRT | IC LED DRIVER |
| SC667ULTRT | IC LED DRVR LMU 7CH MLPQUT20 |
| SC668ULTRT | IC LED DRVR LMU 8CH MLPQUT20 |
| SDIN2B2-8G | IC INAND FLASH 8GB 169FBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC619 | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Charge Pump Flash LED Driver with Safety Timer |
| SC619_08 | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Charge Pump Flash LED Driver with Safety Timer |
| SC619EVB | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Charge Pump Flash LED Driver with Safety Timer |
| SC619ULTRT | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Charge Pump Flash LED Driver with Safety Timer |
| SC620 | 功能描述:UPS - 不间断电源 620VA/390W 4 Outlet RoHS:否 制造商:Phoenix Contact 功率额定值: 输出电压额定值:24 V 出口数量:2 运行时间（满载）: 运行时间（半载）: |
发布紧急采购，3分钟左右您将得到回复。