参数资料
| 型号： | SC806IMLTRT |
| 厂商： | Semtech |
| 文件页数： | 6/13页 |
| 文件大小： | 0K |
| 描述： | IC LI-ION BATT CHARGER 10-MLP |
| 标准包装： | 1 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子，镍镉，镍氢 |
| 电源电压： | 3.15 V ~ 6.3 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-VFDFN 裸露焊盘 |
| 供应商设备封装： | 10-MLP-EP（3x3） |
| 包装： | 标准包装 |
| 产品目录页面： | 1359 (CN2011-ZH PDF) |
| 其它名称： | SC806IMLDKR |
SC806
POWER MANAGEMENT
? ? ? 100
ITERM = ? ?
General Operation
The SC806 is configured based on the application for
Fast Charge and Termination current. A typical charging
cycle is described below. Details on alternate applica-
tions and output programmability are covered in the indi-
vidual sections.
The charging cycle begins when the adapter is plugged
in. The SC806 performs glitch filtering on the VCC input
and initiates a charge cycle when VCC > UVLO. At this
time, the CHRGB and CPB signals are active low turning
on the LEDs. If the battery voltage is less than 2.8V, the
SC806 will charge the output with the pre-charge cur-
rent. When the battery voltage exceeds 2.8V, the SC806
enters fast-charge or constant current (CC) mode. When
the battery voltage reaches its final value, the charger
enters the constant voltage (CV) mode. In this mode the
output voltage is held constant and the current de-
creases until the termination current level is reached.
At this point the charger enters monitor mode and the
CHRGB output is high impedance. The charger output
remains off in monitor mode until Vout drops by 100mV
and a new charge cycle is initiated.
Pre-Charge Mode
Pre-charge mode is automatically enabled whenever the
battery voltage is below 2.8V. It is used to limit the power
dissipation and precondition the battery for fast charg-
ing. The pre-charge current value is selected by the re-
sistor on the ITERM pin. The pre-charge current is pro-
grammable from 10mA to 125mA. The equation to se-
lect the pre-charge current is given by:
Note that for a given program resistor the current through
the battery in CV mode can be determined by replacing
1.5 with the actual voltage on the IPRGM pin in the above
equation.
Termination Current
Once the battery reaches the program voltage of 4.2V
the device will transition from a constant current source
to a constant voltage source and the current through
the battery begins to decrease while the voltage remains
constant. When the current falls below the programmed
termination current set by the termination resistor on
the ITERM pin, the SC806 will transition the CHRGB pin
from low to high. The equation to set the termination
current is given by:
? 1.5 ?
? R TERM ?
Monitor Mode
When a charge cycle is completed, the SC806 output
turns off and the device enters monitor mode. If the
voltage of the battery falls below the recharge threshold
of 4.1V the charger will re-initiate a charge cycle. The
maximum current drain of the battery during monitor
mode will be no more than 1μA over temperature
NTC Input/NOBAT output
The SC806 detects the absence of the battery by moni-
toring the voltage on the NTC pin. When the NTC pin
voltage exceeds 90% of VCC the NOBAT output is driven
PCI = ? ?
? ? ? 100
? 1.5
? R TERM
?
?
high. This function utilizes the standard NTC configura-
tion with the NTC component residing in the battery pack.
When the battery is removed the NTC element in the
? ?
FCI = ?
? ? 1000
? R ?
Fast-Charge Mode (CC)
The fast-charge or CC mode is active when the battery
voltage is above 2.8V and less than the 4.2V CV voltage
of the battery. The fast-charge current can be set to a
maximum of 1.0A and is selected by the program resis-
tor on the IPRGM pin. The voltage on this pin will repre-
sent the current through the battery enabling a micro-
processor to monitor battery current by sensing the volt-
age on the IPRGM pin. The equation to set the fast-
charge current is given by:
1.5
? PRGM ?
resistor divider is missing and the NTC voltage is pulled
up to VCC.
The NOBAT output can be used to signal the system that
the battery has been removed or drive an external LED.
DIS Device Disable Interface
The DIS pin on the SC806 is used to shutdown the SC806
charger. This pin must be pulled low to enable the charger,
high will disable the charger (do not leave floating). The
CPB output indicating the adapter input status is active
regardless of the state of DIS.
? 2004 Semtech Corp.
6
www.semtech.com
相关PDF资料 |
PDF描述 |
|---|---|
| SC810ULTRT | IC BATTERY MANAGEMENT |
| SC811ULTRT | IC BATTERY MANAGEMENT |
| SC824ULTRT | IC BATTERY MANAGEMENT |
| SC900841JVKR2 | IC POWER MGT 338-MAPBGA |
| SC900AMLTRT | IC REG LDO ADJ .2A/.15A 20-MLPQ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC8085 | 制造商:STCHIP 制造商全称:STCHIP 功能描述:85秒语音OTP芯片，5V供电单片机串行控制分段。 |
| SC80905-1 | 制造商:Panasonic Industrial Company 功能描述:SPEAKER |
| SC80C31ACCN40 | 制造商:North American Philips Discrete Products Div 功能描述:Manufacturer Supplied Status Information |
| SC80C31BACA44 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:CMOS single-chip 8-bit microcontrollers |
| SC80C31BACB44 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:CMOS single-chip 8-bit microcontrollers |
发布紧急采购，3分钟左右您将得到回复。