参数资料
| 型号： | SCC2692AC1A44,512 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 11/30页 |
| 文件大小： | 0K |
| 描述： | IC UART DUAL 44-PLCC |
| 产品培训模块： | Stand-Alone UARTs |
| 标准包装： | 26 |
| 特点： | 故障启动位检测 |
| 通道数： | 2，DUART |
| FIFO's： | 3 位 |
| 电源电压： | 5V |
| 带并行端口： | 是 |
| 带自动流量控制功能： | 是 |
| 带故障启动位检测功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-LCC（J 形引线） |
| 供应商设备封装： | 44-PLCC |
| 包装： | 管件 |
| 产品目录页面： | 828 (CN2011-ZH PDF) |
| 其它名称： | 568-1119-5 933968320512 SCC2692AC1A44 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
Philips Semiconductors
Product specification
SCC2692
Dual asynchronous receiver/transmitter (DUART)
1998 Sep 04
19
data clock. The formula for calculating the divisor n to load to the
CTUR and CTLR for a particular 1X data clock is shown below:
n
+
counter clock frequency
16x2x baud rate desired
Often this division will result in a non-integer number; 26.3, for
example. One can only program integer numbers in a digital divider.
Therefore, 26 would be chosen. This gives a baud rate error of
0.3/26.3 which is 1.14%; well within the ability asynchronous mode
of operation.
If the value in CTUR and CTLR is changed, the current half-period
will not be affected, but subsequent half periods will be. The C/T will
not be running until it receives an initial ‘Start Counter’ command
(read at address A3-A0 = 1110). After this, while in timer mode, the
C/T will run continuously. Receipt of a start counter command (read
with A3-A0 = 1110) causes the counter to terminate the current
timing cycle and to begin a new cycle using the values in CTUR and
CTLR.
The counter ready status bit (ISR[3]) is set once each cycle of the
square wave. The bit is reset by a stop counter command (read with
A3-A0 = H‘F’). The command however, does not stop the C/T. The
generated square wave is output on OP3 if it is programmed to be
the C/T output.
In the counter mode, the C/T counts down the number of pulses
loaded into CTUR and CTLR by the CPU. Counting begins upon
receipt of a start counter command. Upon reaching terminal count
H‘0000’, the counter ready interrupt bit (ISR[3]) is set. The counter
continues counting past the terminal count until stopped by the CPU.
If OP3 is programmed to be the output of the C/T, the output
remains High until terminal count is reached, at which time it goes
Low. The output returns to the High state and ISR[3] is cleared when
the counter is stopped by a stop counter command. The CPU may
change the values of CTUR and CTLR at any time, but the new
count becomes effective only on the next start counter commands. If
new values have not been loaded, the previous count values are
preserved and used for the next count cycle
In the counter mode, the current value of the upper and lower 8 bits
of the counter (CTU, CTL) may be read by the CPU. It is
recommended that the counter be stopped when reading to prevent
potential problems which may occur if a carry from the lower 8 bits
to the upper 8 bits occurs between the times that both halves of the
counter are read. However, note that a subsequent start counter
command will cause the counter to begin a new count cycle using
the values in CTUR and CTLR.
RESETN
tRES
SD00133
Figure 3. Reset Timing
相关PDF资料 |
PDF描述 |
|---|---|
| SCC2692AC1N40,602 | IC UART DUAL 40-DIP |
| SCC2681AC1A44,529 | IC DUART 44-PLCC |
| SCC2681AC1A44,512 | IC UART 44-PLCC |
| SCC2681AC1A44,518 | IC DUART 44-PLCC |
| SC16C652BIB48,151 | IC UART DUAL W/FIFO 48-LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SCC2692AC1A44512 | 制造商:NXP Semiconductors 功能描述:IC DUAL UART FIFO 1MBPS 5. |
| SCC2692AC1A44518 | 制造商:Rochester Electronics LLC 功能描述: 制造商:NXP 功能描述: 制造商:NXP Semiconductors 功能描述: |
| SCC2692AC1A44-S | 功能描述:UART 接口集成电路 5V INDSTRL UART 2 C RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SCC2692AC1B44 | 功能描述:UART 接口集成电路 5V INDSTRL UART 2 C RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SCC2692AC1B44,528 | 功能描述:UART 接口集成电路 5V INDSTRL UART 2 C RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。