- 您现在的位置：买卖IC网 > PDF目录372136 > SE95 (NXP Semiconductors N.V.) Ultra high accuracy digital temperature sensor and thermal WatchdogE PDF资料下载
参数资料
| 型号： | SE95 |
| 厂商： | NXP Semiconductors N.V. |
| 元件分类： | 温度/湿度传感器 |
| 英文描述： | Ultra high accuracy digital temperature sensor and thermal WatchdogE |
| 中文描述： | 超高精度数字温度传感器和热WatchdogE |
| 文件页数： | 2/20页 |
| 文件大小： | 198K |
| 代理商： | SE95 |
Philips Semiconductors
Product data sheet
SE95
Ultra high accuracy digital temperature sensor and
thermal Watchdog
2
2004 Dec 21
GENERAL DESCRIPTION
The SE95 is a temperature-to-digital converter using an on-chip
band-gap temperature sensor and Sigma-delta A-to-D conversion
technique. The device is also a thermal detector providing an
over-temp detection output. The SE95 contains a number of data
registers: Configuration register (Conf) to store the device settings
such as sampling rate, device operation mode, OS operation mode,
OS polarity, and OS fault queue as described in the functional
description section; temperature register (Temp) to store the digital
temp reading, and set-point registers (Tos & Thyst) to store
programmable overtemp shutdown and hysteresis limits, and also
an ID register to store manufacturer numbers. These registers are
accessed by a controller via the 2-wire serial I
2
C-bus interface. The
device includes an open-drain output (OS) which becomes active
when the temperature exceeds the programmed limits. There are
three selectable logic address pins so that eight devices can be
connected on the same bus without address conflict.
The SE95 can be configured for different operation conditions. It can
be set in normal mode to periodically monitor the ambient
temperature, or in shutdown mode to minimize power consumption.
The OS output operates in either of two selectable modes: OS
comparator mode and OS interrupt mode. Its active state can be
selected as either HIGH or LOW. The fault queue that defines the
number of consecutive faults in order to activate the OS output is
programmable as well as the set-point limits.
The temperature register always stores a 13-bit 2’s complement
data giving a temperature resolution of 0.03125
°
C. This high
temperature resolution is particularly useful in applications of
measuring precisely the thermal drift or runaway. For normal
operation and compatibility with the LM75A, only the 11 MSBs are
read, with a resolution of 0.125
°
C to provide the accuracies
specified. To be compatible with the LM75, read only the 9 MSBs.
The device is powered-up in normal operation mode with the OS in
comparator mode, temperature threshold of 80
°
C and hysteresis of
75
°
C, so that it can be used as a stand-alone thermostat with those
pre-defined temperature set points. The conversion rate is
programmable, with a default of 10 conversions/sec.
FEATURES
Pin-for-pin replacement for industry standard LM75/LM75A and
offers improved temperature resolution
Specification of a single part over power supply range from 2.8 V
to 5.5 V.
Small 8-pin package types: SO8 and TSSOP8 (MSOP8)
I
2
C-bus interface to 400kHz with up to 8 devices on the same bus
Power supply range from 2.8 V to 5.5 V
Temperatures range from –55
°
C to +125
°
C
13-bit ADC that offers a temperature resolution of 0.03125
°
C
Temperature accuracy of
±
1
°
C from –25
°
C to +100
°
C
Programmable temperature threshold and hysteresis set points
Supply current of 7.0
μ
A in shut-down mode for power
conservation
Stand-alone operation as thermostat at power-up
ESD protection exceeds 1000 V HBM per JESD22-A114,
150 V MM per JESD22-A115
Latch-up testing is done to JEDEC Standard JESD78 which
exceeds 100 mA
APPLICATIONS
System thermal management
Personal computers
Electronics equipment
Industrial controllers
ORDERING INFORMATION
Type n mber
Type number
Topside mark
Package
Temperature
range
Name
Description
Version
SE95D
SE95
SO8
plastic small outline package; 8 leads; body width 3.9 mm
SOT96-1
–55
°
C to +125
°
C
SE95DP
SE95DP
TSSOP8
plastic thin shrink small outline package; 8 leads;
body width 3 mm
SOT505-1
–55
°
C to +125
°
C
WATCHDOG
is a trademark of National Semiconductor Corporation.
相关PDF资料 |
PDF描述 |
|---|---|
| SEOJ | SURFACE MOUNT HIGH EFFICIENCY RECTIFIER |
| SEOK | SURFACE MOUNT HIGH EFFICIENCY RECTIFIER |
| SEOM | SURFACE MOUNT HIGH EFFICIENCY RECTIFIER |
| SEOA | SURFACE MOUNT HIGH EFFICIENCY RECTIFIER |
| SEOJ | SURFACE MOUNT HIGH EFFICIENT RECTIFIERS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SE95D | 功能描述:板上安装温度传感器 I2C LOCAL +/- 1OC TS RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| SE95D,112 | 功能描述:板上安装温度传感器 I2C LOCAL +/- 1OC TS RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| SE95D,118 | 功能描述:板上安装温度传感器 I2C LOCAL +/- 1OC TS RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| SE95D118 | 制造商:Rochester Electronics LLC 功能描述: 制造商:NXP 功能描述: 制造商:NXP Semiconductors 功能描述: |
| SE95DP | 制造商:NXP Semiconductors 功能描述:IC TEMP SENSOR DIGITAL 8TSSOP 制造商:NXP Semiconductors 功能描述:IC, TEMP SENSOR, DIGITAL, 8TSSOP 制造商:NXP Semiconductors 功能描述:IC, TEMP SENSOR, DIGITAL, 8TSSOP; IC Output Type:Digital; Sensing Accuracy Range: 2C; Sensing Temperature Min:-55C; Sensing Temperature Max:+125C; Supply Voltage Min:2.8V; Supply Voltage Max:5.5V; Sensor Case Style:TSSOP; No. of ;RoHS Compliant: Yes |
发布紧急采购，3分钟左右您将得到回复。