- 您现在的位置：买卖IC网 > PDF目录19639 > SE95D,118 (NXP Semiconductors)IC SENSOR TEMP 2.8-5.5V 8SOIC PDF资料下载
参数资料
| 型号： | SE95D,118 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 6/27页 |
| 文件大小： | 150K |
| 描述： | IC SENSOR TEMP 2.8-5.5V 8SOIC |
| 标准包装： | 1 |
| 功能： | 温度监视系统（传感器），监视器 |
| 传感器类型： | 内部 |
| 感应温度： | -55°C ~ 125°C |
| 精确度： | ±3°C（最小值） |
| 拓扑： | ADC（三角积分型），比较器，振荡器，寄存器库 |
| 输出类型： | 2 线串行，I²C? |
| 输出警报： | 无 |
| 输出风扇： | 是 |
| 电源电压： | 2.8 V ~ 5.5 V |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SO |
| 包装： | 标准包装 |
| 其它名称： | 568-8721-6 |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
SE95_7
?NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 2 September 2009
6 of 27
NXP Semiconductors
SE95
Ultra high accuracy digital temperature sensor and thermal watchdog
7.2 OS output and polarity
The OS output is an open-drain output and its state represents results of the device
watchdog operation as described in
Section
7.1. In order to observe this output state, an
external pull-up resistor is needed. The resistor should be as large as possible, up to
200 k&, to minimize the Temp reading error due to internal heating by the high OS sinking
current.
The OS output active state can be selected as HIGH or LOW by programming bit
OS_POL of register Conf: setting bit OS_POL to logic 1 selects OS active HIGH and
setting to logic 0 sets OS active LOW. At power-up, bit OS_POL is equal to logic 0 and the
OS active state is LOW.
7.3 OS comparator and interrupt modes
As described in
Section
7.1, the OS output responds to the result of the comparison
between register Temp data and the programmed limits, in registers Tos and Thyst, in
different ways depending on the selected OS mode: OS comparator or OS interrupt. The
OS mode is selected by programming bit OS_COMP_INT of register Conf: setting bit
OS_COMP_INT to logic 1 selects the OS interrupt mode, and setting to logic 0 selects the
OS comparator mode. At power-up, bit OS_COMP_INT is equal to logic 0 and the OS
comparator is selected.
The main difference between the two modes is that in OS comparator mode, the OS
output becomes active when Temp has exceeded T
os
and reset when Temp has dropped
below T
hyst
, reading a register or putting the device into shutdown mode does not change
the state of the OS output; while in OS interrupt mode, once it has been activated either
by exceeding T
os
or dropping below T
hyst
, the OS output will remain active indenitely until
reading a register or putting the device into shutdown mode occurs, then the OS output is
reset.
Temperature limits T
os
and T
hyst
must be selected so that T
os
> T
hyst
. Otherwise, the OS
output state will be undened.
7.4 OS fault queue
Fault queue is dened as the number of faults that must occur consecutively to activate
the OS output. It is provided to avoid false tripping due to noise. Because faults are
determined at the end of data conversions, fault queue is also dened as the number of
consecutive conversions returning a temperature trip. The value of fault queue is
selectable by programming the two bits OS_F_QUE[1:0] in register Conf. Notice that the
programmed data and the fault queue value are not the same.
T
ab
le
3 shows the
one-to-one relationship between them. At power-up, fault queue data = 00 and fault queue
value = 1.
Table 3.
Fault queue table
Fault queue data
Fault queue value
OS_F_QUE[1]
OS_F_QUE[0]
Decimal
0
0
1
0
1
2
1
0
4
1
1
6
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B04-CY-F4 | CONVERTER MOD DC/DC 48V 50W |
| VE-BV0-CY-F1 | CONVERTER MOD DC/DC 5V 50W |
| HCM02DSXN | CONN EDGECARD 4POS DIP .156 SLD |
| ATF1508AS-7JC84 | IC CPLD 7NS 84PLCC |
| TAJS155M020RNJ | CAP TANT 1.5UF 20V 20% 1206 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SE95DP | 制造商:NXP Semiconductors 功能描述:IC TEMP SENSOR DIGITAL 8TSSOP 制造商:NXP Semiconductors 功能描述:IC, TEMP SENSOR, DIGITAL, 8TSSOP 制造商:NXP Semiconductors 功能描述:IC, TEMP SENSOR, DIGITAL, 8TSSOP; IC Output Type:Digital; Sensing Accuracy Range: 2C; Sensing Temperature Min:-55C; Sensing Temperature Max:+125C; Supply Voltage Min:2.8V; Supply Voltage Max:5.5V; Sensor Case Style:TSSOP; No. of ;RoHS Compliant: Yes |
| SE95DP,118 | 功能描述:板上安装温度传感器 TEMP SENSOR DIGITAL RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| SE95DP,118-CUT TAPE | 制造商:NXP 功能描述:SE95D Series 2.8 V to 5.5 V 1% Accuracy Digital Temperature Sensor - TSSOP-8 |
| SE95DP118 | 制造商:NXP Semiconductors 功能描述:DIGITAL TEMP SENSOR IC 11BIT +/-3C TS |
| SE95D-T | 功能描述:板上安装温度传感器 I2C LOCAL +/- 1OC TS RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。