参数资料
| 型号： | SFS2-DC24V |
| 厂商： | Panasonic Electric Works |
| 文件页数： | 5/5页 |
| 文件大小： | 0K |
| 描述： | RELAY SAFETY 4PST 6A 24V |
| 标准包装： | 20 |
| 系列： | SFS |
| 继电器类型： | 安全 |
| 线圈类型： | 无锁存 |
| 线圈电流： | 15mA |
| 线圈电压： | 24VDC |
| 触点形式： | 4PST（2 A 型，2 B 型） |
| 触点额定值（电流）： | 6A |
| 切换电压： | 250VAC，30VDC - 最小值 |
| 关闭电压（最大）： | 18 VDC |
| 关闭电压（最小）： | 2.4 VDC |
| 安装类型： | 通孔 |
| 端接类型： | PC 引脚 |
| 包装： | 散装 |
| 触点材料： | 银锡氧化物（AgSnO） |
| 操作时间： | 20ms |
| 释放时间： | 20ms |
| 线圈功率： | 360 mW |
| 线圈电阻： | 1.6 千欧 |
| 工作温度： | -40°C ~ 85°C |
| 相关产品： | 255-3099-ND - SOCKET RELAY DIN MNT FOR 4P 255-3098-ND - SOCKET RELAY PCB FOR 4P SF |
| 其它名称： | 255-3095 |
SFS
NOTES
1. Coil operating power
Pure DC current should be applied to the
coil. The wave form should be
rectangular. If it includes ripple, the ripple
factor should be less than 5%. However,
check it with the actual circuit since the
characteristics may be slightly different.
2. Coil connection
When connecting coils, refer to the wiring
diagram to prevent mis-operation or
malfunction.
3. Cleaning
This relay is not sealed, therefore,
immersion may cause failure. Be careful
that ?ux does not over?ow onto the PC
board or penetrate inside the relay.
4. Soldering
When using automatic soldering, the
following conditions are recommended
1) Preheating: 120 ° C 248 ° F , within 120
Sec (PC board solder surface)
2) Soldering: 260 ° C ± 5 ° C 500 ° F ± 41 ° F ,
within 6 Sec
5. Installation
1) Attach directly to the chassis or use a
DIN rail.
(1) When attaching directly to chassis
? Use a M3.5 screw, spring washer, and
hex nut.
? For the mounting pitch, refer to the
dimensions.
(2) When installing on a DIN rail
? Use a 35 mm 1.378 inch wide DIN rail
(DIN46277).
? Install and remove as shown in the
?gures below.
<When installing>
Push
DIN rail
2) Refer to the ?gure below for applicable
wire-pressed terminals.
(You cannot use round type wire-pressed
terminals.)
6.3 mm max. 3 mm min.
.248 inch max. .118 inch min.
6. Other
1) If the relay has been dropped, the
appearance and characteristics should
always be checked before use.
2) The switching lifetime is de?ned under
the standard test condition speci?ed in
the JIS* C 5442-1996 standard
(temperature 15 to 35 ° C 59 to 95 ° F ,
humidity 25 to 75%). Check this with the
actual product as it is affected by the coil
driving circuit, load type, activation
frequency, activation phase, ambient
conditions and other factors.
Also, be especially careful with loads
such as those listed below.
(1) When used for AC load-operation and
the operating phase is synchronous.
Rocking and fusing can easily occur due
to contact shifting.
(2) During high frequency on/off
operation with certain loads, arcing may
occur at the contacts. This can cause
fusion to Oxygen and Nitrogen gas in the
air creating Nitric Acid (HNO 3 ) which can
cause corrosion to the contacts.
Please see the following countermeasure
examples:
1. Incorporate an arc-extinguishing
circuit.
2. Lower the operating frequency
3. Lower the ambient humidity
3) For secure operations, nominal coil
voltage should be applied. In addition,
please note that pick-up and drop-out
voltage will vary according to the ambient
temperature and operating conditions.
4) Heat, smoke, and/or ?re may occur if
the relay is used outside the allowable
ranges for the coil ratings, contact
7. Usage, transport and storage
conditions
1) Ambient temperature, humidity, and
atmospheric pressure during usage,
transport, and storage of the relay:
(1) Temperature:
–40 to +85 ° C –40 to +185 ° F
(When the temperature is 70 to 80 ° C,
reduce the 6 A max. switching current by
0.1 A/ ° C.)
(2) Humidity: 5 to 85% RH
(Avoid freezing and condensation.)
The humidity range varies with the
temperature. Use within the range
indicated in the graph below.
(3) Atmospheric pressure: 86 to 106 kPa
Temperature and humidity range for
usage, transport, and storage
Humidity, %RH
85
Tolerance range
(Avoid freezing (Avoid
when used at condensation
temperatures when used at
lower than temperatures
0 ° C 32 ° F ) higher than
0 ° C 32 ° F )
5
–40 0 85
–40 +32 +185
Temperature, ° C ° F
2) Condensation
Condensation forms when there is a
sudden change in temperature under
high temperature and high humidity
conditions. Condensation will cause
deterioration of the relay insulation.
3) Freezing
Condensation or other moisture may
freeze on the relay when the
temperatures is lower than 0 ° C 32 ° F . This
causes problems such as sticking of
movable parts or operational time lags.
4) Low temperature and low humidity
At low temperature, low humidity
environments, the plastic becomes brittle.
Please note corrections.
8. Please connect DC coil types with
LED and built-in diode correctly by
<When removing>
Pull
Screwdriver
ratings, operating cycle lifetime, and
other speci?cations. Therefore, do not
use the relay if these ratings are
exceeded. Also, make sure that the relay
is wired correctly.
verifying the coil polarity (“+” and “–
”). Connecting with reverse polarity
will cause the LED not to light and
damage the built-in diode due to its
speci?cation.
5) Incorrect wiring may cause false
operation or generate heat or ?ames.
6) Check the ambient conditions when
storing or transporting the relays and
devices containing the relays. Freezing or
condensation may occur in the relay
causing damage. Avoid exposing the
relays to heavy loads, or strong shock
and vibration.
Panasonic Corporation
Automation Controls Business Unit
industrial.panasonic.com/ac/e
ASCTB119E 201201-T
相关PDF资料 |
PDF描述 |
|---|---|
| OSTVN14A150 | TERM BLOCK RISING CLAMP 14POS |
| HCPL2530 | OPTOCOUPLER TRANS-OUT 2CH 8-DIP |
| OSTHE155040 | CONN TERM BLOCK 15POS 2.54MM |
| OSTHE154040 | CONN TERM BLOCK 15POS 2.5MM |
| OSTHB141181 | CONN TERM BLOCK 14POS 10MM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SFS2-DC48V | 功能描述:RELAY SAFETY 4PST 6A 48V 制造商:panasonic electric works 系列:SFS 包装:散装 零件状态:在售 继电器类型:安全 线圈类型:无锁存 线圈电流:7.5mA 线圈电压:48VDC 触头外形:4PST（2 A 型，2 B 型） 额定接触（电流）:6A 开关电压:250VAC，30VDC - 最大 导通电压（最大值）:36 VDC 关闭电压（最小值）:4.8 VDC 工作时间:20ms 释放时间:20ms 特性:- 安装类型:通孔 端子类型:PC 引脚 工作温度:-40°C ~ 85°C 触头材料:银锡氧化物（AgSnO） 线圈功率:360 mW 线圈电阻:6.4 kOhms 标准包装:50 |
| SFS2D-LFR | 制造商:FRONTIER 制造商全称:Frontier Electronics. 功能描述:2A SUPER FAST RECOVERY SURFACE MOUNT RECTIFIER |
| SFS2E | 制造商:FRONTIER 制造商全称:Frontier Electronics. 功能描述:2A SUPER FAST RECOVERY SURFACE MOUNT RECTIFIER |
| SFS2E-LFR | 制造商:FRONTIER 制造商全称:Frontier Electronics. 功能描述:2A SUPER FAST RECOVERY SURFACE MOUNT RECTIFIER |
| SFS2G | 制造商:FRONTIER 制造商全称:Frontier Electronics. 功能描述:2A SUPER FAST RECOVERY SURFACE MOUNT RECTIFIER |
发布紧急采购，3分钟左右您将得到回复。