- 您现在的位置：买卖IC网 > PDF目录7462 > SFSA16GBU1BR4TO-I-QT-226-STD (Swissbit NA Inc)FLASH SLC UDMA/MDMA/PIO 16GB PDF资料下载
参数资料
| 型号： | SFSA16GBU1BR4TO-I-QT-226-STD |
| 厂商： | Swissbit NA Inc |
| 文件页数： | 29/47页 |
| 文件大小： | 0K |
| 描述： | FLASH SLC UDMA/MDMA/PIO 16GB |
| 标准包装： | 20 |
| 系列： | X-200M |
| 存储容量： | 16GB |
| 存储器类型： | 闪存 - NAND |
| 其它名称： | 1052-1082 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页
Features 0Ah and 8Ah are used to enable and disable Power Level 1 commands. Feature 0Ah is the default
feature for the SSD with extended power as they require Power Level 1 to perform their full set of functions.
Power Enhanced SSDs are required to power up and execute all supported commands and protocols in Power
Level 0, their default feature shall be 8Ah: Disable Power Level 1 Commands. No commands are actually
excluded for such cards in Power Level 0 because no commands require Power Level 1. Features 55h and BBh are
the default features for the SSD; thus, the host does not have to issue this command with these features unless
it is necessary for compatibility reasons.
Feature code 9Ah enables the host to configure the card to best meet the host system’s power requirements.
The host sets a value in the Sector Count register that is equal to one-fourth of the desired maximum average
current (in mA) that the card should consume. For example, if the Sector Count register were set to 6, the card
would be configured to provide the best possible performance without exceeding 24 mA. Upon completion of
the command, the card responds to the host with the range of values supported by the card. The minimum
value is set in the Cylinder Low register, and the maximum value is set in the Cylinder Hi register. The default
value, after a power on reset, is to operate at the highest performance and therefore the highest current mode.
The card shall accept values outside this programmable range, but shall operate at either the lowest power or
highest performance as appropriate.
Features 66h and CCh can be used to enable and disable whether the Power On Reset (POR) Defaults shall be set
when a soft reset occurs. The default setting is to revert to the POR defaults when a soft reset occurs.
6.23 Set max address (F9h)
The Set max address command sets the max address of the drive. It is related to the Host protected Area feature
set. Table 44 defines the Set max address command Byte sequence.
Table 44: Read native max address
Task File Register
7
6
5
4
3
2
1
0
COMMAND
F8h
DRIVE/HEAD
nu
LBA
nu
D
Set max LBA (27:24)
CYLINDER HI
CYLINDER LOW
SECTOR NUM
Set max LBA (23:16)
Set max LBA (15:8)
Set max LBA (7:0)
SECTOR COUNT
FEATURES
nu
Feature
VV
The LBA bit shall be set to one to specify the address is an LBA. DEV shall specify the selected device.
Prerequisites
DRDY set to one. A successful READ NATIVE MAX ADDRESS command shall immediately precede a SET MAX ADDRESS
command.
VV =Value volatile. If bit 0 is set to one, the device shall preserve the maximum values over power-up or
hardware reset. If bit 0 is cleared to zero, the device shall revert to the most recent nonvolatile maximum
address value setting over power-up or hardware reset.
The set max address can be locked/unlocked and secured by password with following features:
Table 45: Set max features
Feature register
00h
01h
02h
03h
04h
05-FFh
Command
Obsolete
SET MAX SET PASSWORD
SET MAX LOCK
SET MAX UNLOCK
SET MAX FREEZE LOCK
Reserved
Typical use of the Set max address (F9h) and Read native max address (F8h) commands would be:
On reset
BIOS receives control after a system reset;
1.
2.
BIOS issues a READ NATIVE MAX ADDRESS command to find the max capacity of the device;
BIOS issues a SET MAX ADDRESS command to the values returned by READ NATIVE MAX ADDRESS;
3. BIOS reads configuration data from the highest area on the disk;
4. BIOS issues a READ NATIVE MAX ADDRESS command followed by a SET MAX ADDRESS command to reset the
device to the size of the file system.
Swissbit AG
Industriestrasse 4-8
Swissbit reserves the right to change products or specifications without notice.
Revision: 1.10
CH-9552 Bronschhofen
Switzerland
X-200m_data_sheet_SA-UxBR_Rev110.doc
Page 29 of 47
相关PDF资料 |
PDF描述 |
|---|---|
| SFSA8192Q1BR4TO-I-DT-226-STD | FLASH SLC UDMA/MDMA/PIO 8GB |
| 4-1437664-1 | CONN BARRIER STRIP 8CIRC .375 |
| SFPA8192Q1BO2TO-I-QT-223-STD | FLASH SSD SMART UDMA 2.5" 8GB |
| 3-1437653-5 | CONN BARRIER STRIP 10CIRC .375 |
| 6432.0153.15 | MOD PWR IN/OUT/SW/1PL QC 1.5 PNL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SFSA16GBU1BR4TO-I-QT-236-STD | 功能描述:Solid State Drive (SSD) 16GB SATA II FLASH - NAND (SLC) mSATA 3.3V 制造商:swissbit na inc. 系列:X-200M 零件状态:有效 存储容量:16GB 存储器类型:FLASH - NAND（SLC） 外形尺寸:mSATA 速度 - 读取:120MB/s 速度 - 写入:95MB/s 电压 - 电源:3.3V 类型:SATA II 电流 - 最大值:- 工作温度:-40°C ~ 85°C 重量:0.24 盎司（6.84g） 大小/尺寸:50.80mm x 29.85mm x 3.30mm 标准包装:50 |
| SFSA16GBV1BR4TO-C-QT-236-STD | 制造商:SWISSBIT 功能描述:SLIM SATA X-200S DENSITY COMMERCIAL - Trays 制造商:Swissbit 功能描述: |
| SFSA16GBV1BR4TO-I-QT-216-STD | 功能描述:FLASH X-200S SLC SLIM SATA 16GB RoHS:是 类别:计算机，办公室 - 元件，配件 >> 固态硬盘驱动器 系列:X-200S 标准包装:1 系列:- 存储容量:64GB 存储器类型:闪存 - NAND 其它名称:VL 64 GB SSHD KITVL64GBSSHDKIT |
| SFSA16GBV1BR4TO-I-QT-226-STD | 功能描述:FLASH SLC UDMA/MDMA/PIO 16GB RoHS:是 类别:计算机，办公室 - 元件，配件 >> 固态硬盘驱动器 系列:X-200S 标准包装:1 系列:- 存储容量:64GB 存储器类型:闪存 - NAND 其它名称:VL 64 GB SSHD KITVL64GBSSHDKIT |
| SFSA16GBV1BR4TO-I-QT-236-STD | 制造商:SWISSBIT 功能描述:SLIM SATA X-200S DENSITY INDUSTRIAL - Trays 制造商:SWISSBIT NA INC 功能描述:SSD SLIMSATA IND 16GB 5V 制造商:Swissbit 功能描述: |
发布紧急采购，3分钟左右您将得到回复。