- 您现在的位置：买卖IC网 > PDF目录16381 > SI2400URT-EVB (Silicon Laboratories Inc)BOARD EVAL FOR SI2400 ISOMODEM PDF资料下载
参数资料
| 型号： | SI2400URT-EVB |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 35/94页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR SI2400 ISOMODEM |
| 标准包装： | 1 |
| 系列： | ISOmodem® |
| 主要目的： | 电信，调制解调器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | SI2400 |
| 主要属性： | 双路 RJ-11 连接至电话线路，音频连接器 |
| 次要属性： | RS-232，TTL 串行和 USB 接口 |
| 已供物品： | 板，调制解调器，电源 |
| 相关产品： | SI2400-BS-ND - IC ISOMODEM SYSTEM-SIDE 16SOIC SI2400-FS-ND - IC ISOMODEM SYST-SIDE DAA 16SOIC 336-1093-ND - IC ISOMODEM SYSTEM-SIDE 16SOIC |
| 其它名称： | 336-1166 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页当前第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页
Si2400
40
Rev. 1.3
7. Low Level DSP Control
Although not necessary for most applications, the DSP
low-level control functions are available for users with
very specific applications requiring direct DSP control.
7.1. DSP Registers
Several DSP registers are accessible through the
Si2400 microcontroller via S-registers SE5, SE6, SE7
and SE8. SE5 and SE6 are used as conduits to write
data to specific DSP registers and read status. SE8
defines the function of SE5 and SE6 depending on
whether they are being written to or read from. Care
must be exercised when writing to DSP registers. DSP
registers can only be written while the Si2400 is on-
hook and in the Command mode. Writing to any register
range values is likely to cause the DSP to exhibit
unpredictable behavior.
The DSP register address is 16-bits wide and the DSP
data field is 14-bits wide. DSP register addresses and
data are written in hexadecimal. To write a value to a
DSP register, the register address is written then the
data is written. When SE8 = 0x00, SE5(DADL) is written
with the low bits [7:0] of the DSP register address and
SE6 (DADH) is written with the high bits [15:8] of the
DSP address. When SE8 = 0x01, SE5 (DDL) is written
with the low bits [7:0] of the DSP data word
corresponding to the previously written address and
SE6 (DDH) is written with the high bits [15:8] of the data
word corresponding to the previously written address.
Example 1 below illustrates the proper procedure for
writing to DSP registers.
Example1:
The user would like to program call
progress filter coefficient A2_k0 (0x15) to be 309
(0x135).
Host
Command:
ATSE8=00SE6=00SE5=15SE8=01SE6=01SE5=35SE8=00
In the command above, ATSE8=00 sets up registers
SE5 and SE6 as DSP address registers. SE6=00 sets
the high bits of the address, and SE5=15 sets the low
bits. SE8=01 sets up registers SE5 and SE6 as DSP
data registers for the previously written DSP address
(0x15). SE6=01 sets the high 6 bits of the 14-bit data
word, and SE5=35 sets the low 8 bits of the 14-bit data
word.
Table 24. Low-Level DSP Parameters
DSP Reg. Addr.
Name
Description
Function
Default
(dec)
0x0002
XMTL
DAA modem full scale transmit level,
default = –10 dBm
Level = 20log10 (XTML/4096)
–10 dBm
4096
0x0003
DTML
DTMF high tone transmit level,
default = –5.5 dBm
Level = 20log10 (DTML/4868)
–5.5 dBm
4868
0x0004
DTMT
DTMF twist ratio (low/high), default = –2 dBm Level = 20log
10 (DTMT/3277) –
2dB
3277
0x0005
UFRQ User-defined transmit tone frequency. See
register SE5 (SE8=0x02 (Write Only))
f = (9600/512) UFRQ (Hz)
91
0x0006
CPDL
Call progress detect level (see Figure 13),
default = –43 dBm
Level = 20log10 (4096/CPDL)
–43 dBm
4096
0x0007
UDFD1 User-defined frequency detector 1. Center
frequency for detector 1.
UDFD1 = 8192 cos (2
π f/9600)
4987
0x0008
UDFD2 User-defined frequency detector 2. Center
frequency for detector 2.
UDFD2 = 8192 cos (2
π f/9600)
536
0x0009
UDFD3 User-defined frequency detector 3. Center
frequency for detector 3.
UDFD3 = 8192 cos (2
π f/9600)
4987
0x000A
UDFD4 User-defined frequency detector 4. Center
frequency for detector 4.
UDFD4 = 8192 cos (2
π f/9600)
536
0x000B
TGNL
Tone generation level associated with TONC
(SE5 (SE8 = 0x02) Write Only Definition),
default = –10 dBm
Level = 20log10 (TGNL/2896)
– 10 dBm
2896
相关PDF资料 |
PDF描述 |
|---|---|
| CM322522-1R8JL | INDUCTOR CHIP 1.8UH 3225 SMD |
| 496837-000 | CABLE TERMINATION RG/U 178,404 |
| VI-J72-EX | CONVERTER MOD DC/DC 15V 75W |
| 6374615-8 | C/A LC-SC DUP 62.5/125, 8M |
| VE-B12-EY-S | CONVERTER MOD DC/DC 15V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI2401 | 制造商:SILABS 制造商全称:SILABS 功能描述:V.22BIS ISOMODEM㈢ WITH LOW-COST DAA |
| SI2401-C-FS | 制造商:Silicon Laboratories Inc 功能描述: |
| SI2401DC-EVB | 功能描述:子卡和OEM板 SI2401 Daughter Card RoHS:否 制造商:BeagleBoard by CircuitCo 产品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| SI2401-FS | 功能描述:电信线路管理 IC 2400b/s System Side 3rd Gen DAA Tech RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| Si2401FS08-EVB | 功能描述:网络开发工具 Si2401+Si3008 ISO modem Eval Board RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V |
发布紧急采购，3分钟左右您将得到回复。