参数资料
型号: SI3016-F-FS
厂商: Silicon Laboratories Inc
文件页数: 38/50页
文件大小: 0K
描述: IC LINE-SIDE DAA 16SOIC
标准包装: 48
数据格式: V.90
电源电压: 3.3V,5V
安装类型: 表面贴装
封装/外壳: 16-SOIC(0.154",3.90mm 宽)
供应商设备封装: 16-SOIC N
包装: 管件
Si3016
Rev. 1.0
43
APPENDIX B—CISPR22 COMPLIANCE
Various countries are expected to adopt the IEC
CISPR22 standard over the next few years. For
example, the European Union (EU) has adopted a
standard entitled EN55022, which is based on the
CISPR22 standard. Adherence to this standard will be
necessary to display the CE mark on designs intended
for sale in the EU. The typical schematic and global bill
of
materials
(BOM)
(see
and
contained in this data sheet are designed to be
compliant to the CISPR22 standard.
If smaller inductors are desired, a notch filter may be
used and compliance to CISPR22 still achieved. As
shown in Figure 17, a series capacitor-resistor in
parallel with L1 and L2 forms the simple notch filter.
Table 14 shows corresponding values used for C24,
C25, C38, C39, L1, L2, R31, and R32.
Figure 17. Notch Filter for CISPR22
Compliance
The direct current resistance (DCR) of the listed
inductors is an important consideration. If the DCR of
the inductors used is less than 3
Ω each, then country
PTT specifications which require 300
Ω or less of dc
resistance at TIP and RING with 20 mA of loop current
can be satisfied with the Japan dc termination mode. If
the DCR of the inductors is at or slightly above 3
Ω, the
low-voltage termination mode may need to be used to
satisfy the 300
Ω dc resistance requirement at 20 mA of
loop current. In all cases, "4.9. DC Termination
Considerations" on page 17 should be followed.
If compliance to the CISPR22 standard and certain
other country PTT requirements are not desired, then
L1 and L2 may be removed. If these inductors are
removed, C24 and C25 should be increased to 2200 pF,
and C9 should be changed to 22 nF, 250 V. With these
changes, PTT compliance in the following countries will
not be achieved: India (I/Fax-03/03 standard), Taiwan
(ID0001 standard), Chile (Decree No. 220 1981
standard), and Argentina (CNC-St2-44.01 standard).
For questions concerning compliance to CISPR22 or
other relevant standards, contact a Silicon Laboratories
technical representative.
Table 14. Notch Filter Component Values
C24/C25
C38/C39
L1/L2
R31/R32
1000pF
33pF,
50 V
150 H, DCR
<3
Ω, I >120 mA
680
Ω,
1/10 W
C38
C24
L1
R31
FB1
TIP
To
DAA
C39
C25
L2
R32
FB2
RING
相关PDF资料
PDF描述
PIC16C62A/JW IC MCU EPROM 2KX14 PWM 28CDIP
PIC14000/JW IC MCU OTP 4KX14 A/D 28CDIP
PIC16C622/JW IC MCU EPROM 2KX14 COMP 18CDIP
PIC16C55-RCE/P IC MCU OTP 512X12 28DIP
PIC16C54A/JW IC MCU EPROM 512X12 18CDIP
相关代理商/技术参数
参数描述
SI3016-F-FSR 功能描述:电信线路管理 IC Line-Side device Processor Integrated RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray
SI3016-F-KS 制造商:Silicon Laboratories Inc 功能描述:
SI3016-F-KSR 制造商:Silicon Laboratories Inc 功能描述:
SI3016-FS 功能描述:IC LINE-SIDE DAA 16SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 调制解调器 - IC 和模块 系列:- 标准包装:25 系列:- 数据格式:V.21,V.22,V.23,V.29,V.32,V.34,V.90,V.92,Bell 103,Bell 212A 波特率:33.6k 电源电压:3.3V 安装类型:- 封装/外壳:- 供应商设备封装:- 包装:托盘 配用:591-1013-ND - KIT DEV SOCKETMODEM PARALLEL591-1009-ND - KIT DEV SRL SOCKETMODEM UNIVERSL 其它名称:MT5656SMI-P-V-34.R2-SPMT5656SMI-P-V-34.R2-SP-NDQ4711574
SI3016-FSR 功能描述:IC LINE-SIDE DAA 16SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 调制解调器 - IC 和模块 系列:- 标准包装:25 系列:- 数据格式:V.21,V.22,V.23,V.29,V.32,V.34,V.90,V.92,Bell 103,Bell 212A 波特率:33.6k 电源电压:3.3V 安装类型:- 封装/外壳:- 供应商设备封装:- 包装:托盘 配用:591-1013-ND - KIT DEV SOCKETMODEM PARALLEL591-1009-ND - KIT DEV SRL SOCKETMODEM UNIVERSL 其它名称:MT5656SMI-P-V-34.R2-SPMT5656SMI-P-V-34.R2-SP-NDQ4711574