- 您现在的位置：买卖IC网 > PDF目录16210 > SI3056DC-EVB (Silicon Laboratories Inc)DAUGHTERCARD DAA SI3056/SI3018 PDF资料下载
参数资料
| 型号： | SI3056DC-EVB |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 26/94页 |
| 文件大小： | 0K |
| 描述： | DAUGHTERCARD DAA SI3056/SI3018 |
| 标准包装： | 1 |
| 主要目的： | 电信，数据采集装置（DAA） |
| 已用 IC / 零件： | Si3056 |
| 已供物品： | 板，CD |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页
Si3056
Si3018/19/10
32
Rev. 1.05
Figure 22. Billing Tone Filter
L1 must carry the entire loop current. The series
resistance of the inductors is important to achieve a
narrow and deep notch. This design has more than
25 dB of attenuation at both 12 kHz and 16 kHz.
The billing tone filter affects the ac termination and
return loss. The global complex ac termination
(ACIM = 1111) passes global return loss specifications
with and without the billing tone filter by at least 3 dB.
5.20. On-Hook Line Monitor
The on-hook line monitor mode allows the Si3056 to
receive line activity when in an on-hook state. A low-
power ADC located on the line-side device digitizes the
signal passed across the RNG1/2 pins and then sends
the signal digitally across the communications link to the
host. This mode is typically used to detect caller ID data
and is enabled by setting the ONHM bit (Register 5,
bit 3). Caller ID data can be gained up or attenuated
using the receive gain control bits in registers 39 and
41.
5.21. Caller ID
The Si3056 can pass caller ID data from the phone line
to a caller ID decoder connected to the serial port.
5.21.1. Type I Caller ID
Type I Caller ID sends the CID data while the phone is
on-hook.
In systems where the caller ID data is passed on the
phone line between the first and second rings, utilize the
following method to capture the caller ID data:
1. After identifying a ring signal using one of the
methods described in "5.14.Ring Detection" on page
29, determine when the first ring is complete.
2. Assert the ONHM bit (Register 5, bit 3) to enable
caller ID data detection. The caller ID data passed
across the RNG 1/2 pins is presented to the host via
the SDO pin.
3. Clear the ONHM bit after the caller ID data is
received.
In systems where the caller ID data is preceded by a
line polarity (battery) reversal, use the following method
to capture the caller ID data:
1. Enable full wave rectified ring detection (RFWE,
Register 18, bit 1).
2. Monitor the RDTP and RDTN register bits (or the
POLI bit) to identify whether a polarity reversal or
ring signal has occurred. A polarity reversal trips
either the RDTP or RDTN ring detection bits, and
thus the full-wave ring detector must be used to
distinguish a polarity reversal from a ring. The lowest
specified ring frequency is 15 Hz; therefore, if a
battery reversal occurs, the DSP should wait a
minimum of 40 ms to verify that the event observed
is a battery reversal and not a ring signal. This time
is greater than half the period of the longest ring
signal. If another edge is detected during this 40 ms
pause, this event is characterized as a ring signal
and not a battery reversal.
3. Assert the ONHM bit (Register 5, bit 3) to enable the
caller ID data detection. The caller ID data passed
across the RNG 1/2 pins is presented to the host via
the SDO pin.
4. Clear the ONHM bit after the caller ID data is
received.
5.21.2. Type II Caller ID
Type II Caller ID sends the CID data while the phone is
off-hook and is often referred to as caller ID/call waiting
(CID/CW). To receive the CID data while off-hook, use
the following procedure (see Figure 23):
1. The Caller Alert Signal (CAS) tone is sent from the
Central Office (CO) and is digitized along with the
Table 19. Component Values—Optional Billing
Tone Filters
Symbol
Value
C1,C2
0.027 F, 50 V, ±10%
C3
0.01 F, 250 V, ±10%
L1
3.3 mH, >120 mA, <10
, ±10%
L2
10 mH, >40 mA, <10
, ±10%
L2
C3
RING
TIP
From
Line
To
DAA
C1
C2
L1
相关PDF资料 |
PDF描述 |
|---|---|
| GBM31DCCI | CONN EDGECARD 62POS R/A .156 SLD |
| CW252016-39NG | INDUCTOR 39NH 1008 SMD |
| CW252016-33NG | INDUCTOR 33NH 1008 SMD |
| CW252016-27NG | INDUCTOR 27NH 1008 SMD |
| CW252016-22NG | INDUCTOR 22NH 1008 SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| Si3056-D-FS | 功能描述:电信线路管理 IC Si3056 DAA System Side SSI Interface RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI3056-D-FSR | 功能描述:电信线路管理 IC Si3056 DAA System Side SSI Interface RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI3056-D-ZS3R | 制造商:Silicon Laboratories Inc 功能描述:MODEM CHIP CHIPSET 56KBPS - Tape and Reel |
| SI3056-F-FS | 制造商:Silicon Laboratories Inc 功能描述: |
| SI3056-FS | 功能描述:IC SYSTEM-SIDE DAA 16SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 调制解调器 - IC 和模块 系列:- 标准包装:25 系列:- 数据格式:V.21，V.22，V.23，V.29，V.32，V.34，V.90，V.92，Bell 103，Bell 212A 波特率:33.6k 电源电压:3.3V 安装类型:- 封装/外壳:- 供应商设备封装:- 包装:托盘 配用:591-1013-ND - KIT DEV SOCKETMODEM PARALLEL591-1009-ND - KIT DEV SRL SOCKETMODEM UNIVERSL 其它名称:MT5656SMI-P-V-34.R2-SPMT5656SMI-P-V-34.R2-SP-NDQ4711574 |
发布紧急采购，3分钟左右您将得到回复。