- 您现在的位置：买卖IC网 > Datasheet目录356 > SI3460-EVB (Silicon Laboratories Inc)BOARD EVAL POE FOR SI3460 Datasheet资料下载
参数资料
| 型号： | SI3460-EVB |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 6/26页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL POE FOR SI3460 |
| 标准包装： | 1 |
| 主要目的： | 特殊用途 DC/DC，以太网供电（POE） |
| 输出及类型： | 1，非隔离 |
| 功率 - 输出： | 4W，7W，15.4W |
| 输出电压： | -48V |
| 电流 - 输出： | 83mA，146mA，321mA |
| 输入电压： | 11 ~ 16 V |
| 稳压器拓扑结构： | 升压 |
| 频率 - 开关： | 250kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | Si3460 |
| 其它名称： | 336-1842 |
Si3460-EVB
5.2. CTRL1 and CTRL2
These two pins are the output of two 96 kHz 8-bit pulse width modulators. The output of these pins is averaged
using R15, R29, and C5 to produce a dc level across C5 that is controllable with 16-bit resolution. This dc voltage
is used to control both the detection process and the pulse width modulator for the dc-dc converter.
5.3. Detection
During the detection phase, the pass transistor M2 is held off by driving the GATE pin high. The 250 kHz clock for
the PWM circuit is held low, forcing the switcher FET M1 off.
In the detect state, the output voltage is determined by the output of U18A feeding the resistive bridge R1, R2, and
R3. The PD at the other end of a cable forms the fourth leg of the bridge. The return path to Vee is through D8 and
L1. The bridge null is read through amplifier U18B, which is fed to the Si3460 pin DETA.
The output of U18A is controlled by the CTRL1 and CTRL2 pins as noted earlier. For most of the detection cycle,
the CTRL pins are held high which forces U18A low, producing no output. The bridge voltage is varied to force
IEEE compliant detection voltages of approximately 4.5 and 7.5 V across the bridge with 20 ms delay and robust
three-point detection algorithm at 4.5, 7.5, and back to 4.5 V. To robustly insure that the PD has a valid resistive
signature, the bridge null is checked as the voltage increases and then checked again as the voltage decreases.
Relevant waveforms are shown in Figure 4 and Figure 5 on page 11.
5.4. PWM
In order to apply power to the load, M2 is turned on by driving the Si3460's GATE pin high. At the same time, the
PWM circuitry is enabled by turning on the 250 kHz clock (250 kHz pin). The 250 kHz square wave is converted to
a triangular shape by the filter R14 and C6. The dc level set by CTRL1 and CTRL2 is used to control the PWM
comparator U19B that drives the switcher FET through gate driver U3.
The output voltage is sensed through resistor divider R43 and R44, and the output current is sensed through
resistor R4. The Si3460 integrates an A/D that measures these quantities and varies the CTRL1 and CTRL2 duty
cycle to regulate the output current and voltage as desired.
5.5. Classification
For classification, M2 is turned on and the PWM is enabled. The Si3460 is programmed to perform classification at
18 V output voltage, with a current limit of between 50 and 100 mA. Classification is performed after allowing 20 ms
of settling time.
Since the Si3460-EVB is designed for a single port PSE application, the classification information is only used to
determine if the load is in the range that is supported, according to the mode of the Si3460 determined at power up
(refer to STATUS pin in Section “5.1. Initialization and Operating Mode Configuration”).
Table 3. Classification Levels
Classification
Mode
Full power
Class 1 only
PSE Minimum
Output Power
15.4 W
4W
Action Performed
Always apply full power
Only apply power if the current
Overload Current
Threshold I CUT (Max)
400 mA
98 mA
Overload Current
Limit I LIM (Max)
450 mA
450 mA
is between 8 and 13 mA
(class 1)
Class 1 or Class 2
7W
Only apply full power if the
180 mA
450 mA
current is between 8 and
21 mA (class 1 or class 2)
If the measured classification level is not in the supported range, an error is declared and the Si3460 will either time
out and retry and wait for a reset as determined by the power up mode of operation. Relevant waveforms are
shown in Figure 5 on page 11 and Figure 6 on page 12. If the class level is in the supported range, the Si3460
proceeds to powerup.
6
Rev. 1.2
相关PDF资料 |
PDF描述 |
|---|---|
| SI8220BD-A-IS | IC ISODRIVER 2.5A OPTO IN 16SOIC |
| SI8402AB-B-IS | IC I2C ISOLATOR BIDIR 8-SOIC |
| SI8405AB-A-IS1 | IC ISOLATOR 10M 6CH 2.5K 16SOIC |
| SI8423BD-B-IS | ISOLATOR 2CH 5KV 150M 16SOIC |
| SI8435BB-C-IS1 | IC ISOLATOR DGTL 3CH 16SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI3460-XYY-GM | 制造商:SILABS 制造商全称:SILABS 功能描述:IEEE 802.3af PSE INTERFACE AND DC-DC CONTROLLER |
| SI3461 | 制造商:SILABS 制造商全称:SILABS 功能描述:SINGLE-PORT IEEE 802.3AT POE/POE+ PSE INTERFACE |
| Si3461-E01-GM | 功能描述:电源开关 IC - POE / LAN Single-Port PoE / PoE+ PSE interface RoHS:否 制造商:Fairchild Semiconductor 开关数量:Single 开关配置:SPST 开启电阻（最大值）:7.3 Ohms 串话: 带宽: 开启时间（最大值）:13 ns 关闭时间（最大值）:20 ns 切换电压（最大）: 工作电源电压:8 V to 26 V 最大工作温度:+ 125 C 安装风格:Through Hole 封装 / 箱体:TO-220F-6 |
| SI3461-E01-GMR | 功能描述:IC POWER MANAGEMENT CTLR 11VQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
| Si3461-E02-GM | 功能描述:电源开关 IC - POE / LAN Single-port PoE PoE+ PSE interface RoHS:否 制造商:Fairchild Semiconductor 开关数量:Single 开关配置:SPST 开启电阻（最大值）:7.3 Ohms 串话: 带宽: 开启时间（最大值）:13 ns 关闭时间（最大值）:20 ns 切换电压（最大）: 工作电源电压:8 V to 26 V 最大工作温度:+ 125 C 安装风格:Through Hole 封装 / 箱体:TO-220F-6 |
发布紧急采购，3分钟左右您将得到回复。